Sporting a wealth of connections and a Gold mount battery plate, RED DIGITAL CINEMA's DSMC2 Production Module is designed to complement professional DSMC2 camera configurations. Compatible with DSMC2 firmware 7.2 or later, this module features two 3G-SDI BNC outputs, one BNC monitor output, two 24V R/S ports, and two full-size XLR audio inputs.

Additional interfaces include genlock, timecode, GigE Ethernet, and RS-232 connectors for data and control functions. LEMO, D-Tap, and USB ports are also available for powering camera accessories. A 3.5mm headphone jack enables you to monitor audio during recording and playback.

For RED DSMC2 Cameras    Uses Standard Gold Mount Battery    Requires DSMC2 Firmware 7.2 or Higher    2 x 3G-SDI Outputs, 1 x Monitor Output    2 x R/S Ports with 24V, 2.5A Output    XLR Mic/Line Inputs with Phantom Power    3.5mm Headphone Output    Genlock, Timecode & DC Input    GIG-E & Control Ports/Power Distribution

• Two front-facing 3-pin Fischer R/S ports support Remote Start/Stop functionality and provide 24V power out (up to a combined 2.5A)
• A front-facing 2-pin LEMO auxiliary port provides power out up to 3.0A
• A 2-pin D-Tap connector on the module's top provides power out up to 3.0A
• A rear-facing USB 2.0 port with support for fast charging provides 5V at 1.5A for a powering small mobile device
• DC power in, genlock, timecode, Gig-E and control ports
• Two 3-pin XLR audio ports each offer +48V phantom power

Related Questions and Answers

Q: 1. What is a bracket that can mount 15mm rods to the two 1/4-20s in the front?

A: This simple Axler Rod Bridge Adapter should do the trick: https://bhpho.to/2KgyKya

Q: 2. Is it compatible with any v-mount battery or red brick only?

A: I know it works with my IDX slims. I think that's the lowest you can go as far as wattage though. Anything from there on up, you should be fine. Honestly though, unless you already have VLock batteries, I'd go for the bricks. Just get two. They last WAY longer and you can see the percentage of battery life on the monitor.

Q: 3. What lens mount adapter support can be used with the expander module... I have the Metabones lens adapter and I can't find a lens support that will fix in front of the Komodo Expander module?

A: Try the using the SmallRig Metabones Lens Adapter Support for BMPCC 4K Cage for lens support with the RED DIGITAL CINEMA KOMODO Expander Module.

Q: 4. Can you run line level audio into the 3.5mm stereo input or is it just a mic level connection?

A: RED describes the 3.5mm input as a Mic Input only. It does not list it as Line Level.

Q: 5. Hello ! Does this fit on KipperTie Chinstrap mount support ?

A: The KipperTie Chinstrap Support comes with side support ribs with two M4 threads that seem to line up with the Wing Grip's M4 mounting points. It would be best to reach out to KipperTie since B&H does not carry their products.

Q: 6. Just to be sure. If the Wing Grip mounts on both sides of Komodo, will it work fine with Komodo Outrigger Handle?

A: Yes, The RED DIGITAL CINEMA KOMODO Wing Grip can mount to either side of the Komodo. If you use the Outrigger handle you would not be able to install a wing grip where the outrigger handle is located. So you would only be able to use the KOMODO Wing Grip on one side when paired with the Outrigger handle.

Q: 7. Will this side handle work with the Dragon-X?

A: Yes it will. The Dragon-X is a DSMC2 camera.

Q: 8. What 80mm Touch and Go quick release adapters work with this?

A: Yes, the RED DIGITAL CINEMA KOMODO Expander Module, is compatible with the GLOBAL DYNAMICS UNITED 80mm Touch N Go System.

Q: 9. Will this work on Gemini?

A: Yes it will.

Q: 10. How much does this weigh?

A: Approximately 0.13 lbs (59 g)​​​​