Add another display to your wireless video system with the Vanco HDMI Wireless Receiver. It works with the Vanco HDWIRKIT and can receive Full HD signals up to 131' from your transmitter.

For Use with the HDWIRKIT    Supports Full HD    IR Pass-Through

• Extends HDMI signals wirelessly up to 131' with the HDWIRKIT wireless extender kit

• Transmits up to 1080p HD video and audio

• Able to split wireless HDMI signals to up to four displays in conjunction with the HDWIRKIT

• Perfect solution where cabling cannot be run such as a mantle or outdoor application

• IR pass-through to control source from display location wirelessly

• No line of sight installation required; wireless signal will pass through most obstacles

• Easy manual front panel or IR setup for multiple units

Related Questions and Answers

Q: 1. If I buy the kit without a V mount plate where can I get it later if I want to? I can't find the same one they use.

A: The Wooden Camera Dual Battery Plate Cradle for Teradek Bolt LT Transmitter (V-Mount) is the respective V-Mount plate for the Teradek Bolt 6 LT HDMI 750 Wireless Receiver.

Q: 2. Does this work with a cameras true 59.97hz rate vs, 60hz?

A: Yes it will.

Q: 3. Can I have two receivers receiving from the same transmitter?

A: Up to three additional separately sold transmitters can be paired with the receiver. But only one receiver may be used in a system.

Q: 4. Can the receive powered by standard USB? How much A?

A: The mini usb can be used for power. The transmitter requires 1A the receiver 1.5A.

Q: 5. Can the Bolt 6 Receiver HDMI receives signal from from a Bolt 6 SDI/HDMI version?

A: The Teradek Bolt 6 LT HDMI 750 Wireless Receiver can receive the signal of any bolt 4K series transmitter, including the transmitters that SDI/HDMI inputs.

Q: 6. What’s comes with the deluxe package ?

A: In the box of the Teradek Bolt 6 LT 750 3G-SDI/HDMI Wireless RX/TX with Case Deluxe Kit (Gold Mount), you will find the following: Teradek Bolt 6 LT 750 3G-SDI/HDMI Wireless RX/TX with Case Deluxe Kit (Gold Mount) Bolt 6 LT 750 3G-SDI/HDMI Transmitter Bolt 6 LT 750 3G-SDI/HDMI Receiver (Gold Mount) 2-Pin to D-Tap Power Cable (18") USB-A 2.0 Male to Micro-USB Male Cable (39") 2 x HDMI Type A Male to HDMI Type A Male Cable (18") 2 x BNC to BNC SDI Cable (10") 2-Pin to 2-Pin Connector for ALEXA (18") AC Adapter with Cable (6') 7 x Antenna 1/4"-20 Light Stand Adapter Shoe Adapter 2 x Screw Wooden Camera Offset Mount Carry Case Limited 1-Year Manufacturer Warranty

Q: 7. Does Bolt 6 HDMI pass start/stop flags of Canon R6 or Red Komodo? (I have tried but I can't get it to work)

A: The Teradek Bolt 6 LT HDMI 750 Transmitter/Receiver Kit is not listed as being able to start/stop camera recording.

Q: 8. Can I use this to monitor the HDMI video signal from a camera on an Android device (with the right cable adapters)?

A: The Vanco HDMI to USB 2.0 Video Capture Device will intake HDMI video signals up to 4K 30P and encoded them for use on smart devices that use Windows, macOS, Linux, or Android.

Q: 9. Can this be used as BOTH a source and display emulator at the same time to test a cable? It says it can be a sig gen OR display

A: According to the manual, there is no mention of dual operation being impossible at the same time when using the Vanco Handheld 4K HDMI Tester.

Q: 10. Does the receiver go to sleep at all?

A: The IOGEAR Wireless HDMI Transmitter and Receiver Kit (BH # IOGWHD11) has a standby mode.