The light beige Countryman E6 Directional Earset Mic, Low Gain with Detachable 2mm Cable and LEMO 3-Pin Connector for Zaxcom Wireless Transmitters is a vocal microphone with an adjustable boom that weighs less than one tenth of an ounce and is designed to be used by only one person. Once adjusted, it will continually hold this shape.

The E6 earset can be used on either ear for capturing audio and rejecting unwanted sound, feedback, or surrounding noise from stage monitors or nearby speakers in houses of worship, theater, and outdoor vocal and speech applications.

The low-profile, directional E6 earset virtually disappears against the skin, so performers will forget they're wearing a mic. This version offers the lowest gain for the most powerful vocals that require the highest overload. Additionally, the earset comes with two pattern-changeable protective caps for maximum isolation and gain before feedback. This directional E6 earset's cable terminates to a LEMO 3-pin connector for direct connection to Zaxcom TRX900AA, TRX900LA, TRX900LT, TRX900LTH, TRX900LTHS, TRX900LTS, TRXFB3, TRXLA2, TRXLA3, TRXLT3, and ZMT3 wireless bodypack transmitters.

For Stage, Theater, and Broadcast TV    Fits Zaxcom Transmitters    Headroom for Strong Vocals    Detachable 2mm Diameter Cable    Stiff, Steel Boom    Includes Windscreen    2 x Protective Caps    Black and White Single Tie Cable Clips    Carrying Case

The Countryman earsets are very small, lightweight, and the least visible headworn microphones.

The classic E6 is a good choice when one person will wear the microphone. Because the boom is stiffer, it can be adjusted to fit, then stored away and quickly reworn.

The E6's stainless steel boom is tough and can be bent and re-bent to fit different performers. It is highly resistant to makeup, sweat, and moisture when used with the supplied protective caps. The earset should always have a protective cap in place to keep sweat, makeup, and other foreign material out of the microphone.

The E6 earset's flexible boom is easily shaped right on the performer's face. Changeable protective caps let you shape the frequency response for different situations or to match other microphones. The directional earset protective caps adjust the pattern from cardioid to hypercardioid.

Easy adjustment keeps the mic in a comfortable position for rejecting unwanted sounds. The directional E6 earset provides more isolation and is suitable for situations where there are loud monitors, extreme feedback, or environmental noise.

The included removable, quick-swap cable detaches from the actual earset, making it completely replaceable in the event of a short or break. The replaceable cable design makes upgrading wireless microphone systems easy as they are available in a wide selection of connections to accommodate most wireless transmitters.

Related Questions and Answers

Q: 1. Is the SDI Cable 3G, 6G or 12G? Want to use it with Red Komodo. Should be 12G.

A: The following cable is 3G sdi.

Q: 2. Well this boom work in other dual port headphones? I.e. Fostex TRP50s?

A: The RODE NTH-Mic Detachable Boom Microphone for NTH-100 Headphones BH #RONTHMIC is only for the headphones listed.

Q: 3. Will this work to power a Small HD Cine 5?

A: No, the Kondor Blue D-Tap to 2-Pin LEMO Braided Cable for RED KOMODO would be only for the RED Komodo camera. Please use the model below which will work correctly with SmallHD displays. D-TAP TO LEMO 2 PIN 0B MALE POWER CABLE FOR Z CAM, SMALLHD, TERADEK BH #KODTAPFLEM2P

Q: 4. Based on the direction of the tentacle, is this version a female 5-pin LEMO? I'm hoping to use to power my nucleus nano from my handle

A: The LEMO connection on this cable is is male, and it is designed for time code to be sent from a Tenacle Sync TC generator to a device with 5-Pin female TC in.

Q: 5. Could I use this cable to sync timecode from my Atomos Shogun (that has a LEMO port) out to my Sound Devices MixPre-3 via the MixPre-3's Aux-in port? I have a Sony A7III that's generating the timecode out to the Shogun. So, essentially, this cable would connect to the Atomos Shogun's LEMO port and the Shogun would be sending the timecode out to the MixPre-3's 3.5mm AUX-IN. And if so, will recording be triggered from camera, to shogun, to the mixpre? I know the Sony will trigger the shogun, but can the shogun trigger the mixpre with the aforementioned setup? Thanks!

A: This cable is not appropriate for the Shogun and MixPre. To connect the Shogun to the MixPre, you would want to connect the HDMI output of the Shogun to the Micro-HDMI connection on the MixPre. This will take the HDMI TC from the Sony to the recorder. The MixPre must be set in HDMI TC Mode and will stop and start recording from the camera triggering it.

Q: 6. I’m confused if this is the cable to jam sync a Tentacle with a Sound Devices 633, or is it the C02?

A: The two cables are directional so it depends on which device you are using to generate timecode and which is receiving timecode. You'll see an arrow on the white band near the 3.5mm connector that shows the direction of signal flow for each cable. The C03 is for sending timecode from the 633 into a Tentacle Sync and the C02 is for sending timecode from a Tentacle Sync into the 633.

Q: 7. Does this work with BMPCC 6K Pro? Thanks.

A: The BMPCC 6K Pro has a 2-pin LEMO port and you will need this instead: Anton Bauer P-Tap to BMPCC 6K/4K 2-Pin LEMO Cable (20") https://www.bhphotovideo.com/c/product/1596766-REG/anton_bauer_8075_0309_p_tap_to_blackmagic_design.html

Q: 8. Can I use this cable to feed time code from a Sound Devices 633 or 702T into the mic in on my Canon 5D mkii?

A: The cable will give you TC out of the SD machines, but I do not believe that the 5D can jam sync internal TC in the camera through a mic input with an AGC. Use a TC slate (Movieslate on an iPad?) which you can jam to the SD machines using this cable, show the camera the slate when you roll, and this will get you close enough to sync double system .wav files in post.

Q: 9. Can this be used for the ZCam M4?

A: Unfortunately we can not say if the Camera Motion Research 36W 2-Pin LEMO to AC Adapter Cable (7') will work, as we can not verify if the polarity matches that of the input on the Z CAM E2-M4. I'd recommend using the GyroVu USB to Sony L-Series Dummy Battery Cable with Power Supply (40")(BH #GYGVUSBSLPS) instead. See: https://bhpho.to/30OkDpW

Q: 10. Will this cable work to jam to a Deity TC-1 box? Same thing, just the Deity?

A: Yes but it is recommended that you use the Deity Microphones C14 instead because of the threaded locking connector.