Hole Reducing Mounting Plate For A Stereo Receiver

Tecnec Wpl-1114tb Stainless Steel 1-gang Wall Plate

Product Code: ga7508
Availability: In Stock

$130.47 $189.18

Qty

9 reviews Write a review

Description
Reviews (9)

The TecNec WPL-1114TB is a stainless steel wall plate featuring two Neutrik 3-pin male XLR connector terminal blocks. This high quality plate has counter-sunk mounting holes, allowing for a flush finish.

(2) Neutrik 3-Pin Male XLR Terminals

Parameters
Dimensions (WxHxD)	2.75 x 4.5" (7 x 11.43cm)
Packaging Info
Package Weight	0.2 lb
Box Dimensions (LxWxH)	3.9 x 2.8 x 1.1"

Related Questions and Answers

Q: 1. what is the distance between the holes?

A: The large Outside holes are 6 centimeters by 13 centimeters on center. The small Inner holes are 4 centimeters by 12 centimeters on center.

Q: 2. Is this compatible with the Matthews BabySitt'r?

A: This is a Baby 5/8 pin it's compatible with any Baby pin accessory.

Q: 3. What is the dimension from the back of the plate to the far end of the receiver?

A: It is about 3 inches from the back of this plate to the far end of the receiver.

Q: 4. Which hole is the "safety cable hole"?

A: safety cable goes on the Baby Pin

Q: 5. Can the handle be removed?

A: Yes the handle can be unscrewed.

Q: 6. What size diameter is the holes or anchor points? I want to secure Kino clips onto them.

A: Think it is 1/4 inch and 1/8 inch for smaller

Q: 7. Is this compatible with Dante?

A: The SoundTools WallCAT WC851 Analog Audio Over Cat5 Wall Plate (White), BH #SOWC851W, is not Dante compatible. It will easily send or receive four channels of XLR, AES3, DMX or intercom over Ethernet cabling to multiple locations.

Q: 8. Is the pin removable?

A: The pin is welded in place.

Q: 9. How big are the holes and what' the spacing? Was thinking of putting some magnets on this and want to get some ideas on sizes

A: The larger holes are 5mm, and the smaller 3mm. From center to center the large holes are 5.5 cm apart. From center to center the small holes are 3.5 cm apart. The entire plate is approximately 7.5cm x 14.5cm

Q: 10. Can this also be used as a junior pin?

A: Remove the screw and it should fit a junior receiver.

anyonymous	26/07/2024
Don't let the picture confuse you; this frame will hold three seperate inserts. Also, the frame ships with three blank inserts in it already. If you are only planning to use two inserts there is no need to purchase a seperate blank insert. Simply remove two blank covers for the inserts you need and leave the third blank cover in place. This product is very easy to install and the inserts fit well and leave a clean finished installation. I am very satisfied with this product as well as the variety of inserts available. 5

Scott	13/07/2024
Perfect for the Neutrik modules. 5

Billy	08/07/2024
B and H has all the equipment we need for out media upgrade project. The wall plate will make it possible to hide all the wiring for our stage rebuild. Great go to for all of our equipment needs. Although this item was on back order in several other vendors, B and H delivered above my expectations. 5

Tim	14/06/2024
What can I say, they are the right size, the right three, and the right quantity! It doesn't get any better than this. Seriously not the easiest size to find, and B&H has them, in both black and silver. 5

paul	05/06/2024
easy to use and working fine 5

Jacob	15/05/2024
Good quality, straightforward install, smooth connection. What is not to like? 5

Michael	03/05/2024
B&H is realy the king,concerning shipping and order accuracy. Everything was well packed . 5

Patrick	27/04/2024
Fit this Neutrik NA3FDM XLR Female to Male Feedthrough Adapter for Panel Mount into a RapcoHorizon SP-1DFN XLR Single Gang Wall Plate with 1 Neutrik NC3FD-L-1 Connector after knocking out the rivets, then re-riveting it to the plate. Then I fit it into a movable pulpit where the original jack had been abused and the soldered connections severed. In a church environment, who can fix that, and who needs downtime? Especially with very young and active kids! 5