The cocoa Countryman E6 Omnidirectional Earset Mic, Low Gain with Detachable 1mm Cable and 1/4" Connector for Line 6 Wireless Transmitters is a vocal microphone with an adjustable boom that weighs less than one tenth of an ounce and is designed to be used by only one person. Once adjusted, it will continually hold this shape.

The E6 earset can be used on either ear for capturing audio and rejecting unwanted sound, feedback, or surrounding noise from stage monitors or nearby speakers in houses of worship, theater, and outdoor vocal and speech applications.

The low-profile, omnidirectional E6 earset virtually disappears against the skin, so performers will forget they're wearing a mic. This version offers the lowest gain for the most powerful vocals that require the highest overload. In addition, the earset comes with three protective caps with different high-frequency response characteristics that control the amount of crispness or sibilance (response at 15 kHz). This omnidirectional E6 earset's cable terminates to a 1/4" connector for direct connection to Line 6 TBP06 wireless bodypack transmitters.

For Stage, Theater, and Broadcast TV    Fits Line 6 Transmitters    Headroom for Strong Vocals    Detachable 1mm Diameter Cable    Stiff, Steel Boom    Includes Windscreen    3 x Protective Caps    Black and White Single Tie Cable Clips    Carrying Case

The Countryman earsets are very small, lightweight, and the least visible headworn microphones.

The classic E6 is a good choice when one person will wear the microphone. Because the boom is stiffer, it can be adjusted to fit, then stored away and quickly reworn.

The E6's stainless steel boom is tough and can be bent and re-bent to fit different performers. It is highly resistant to makeup, sweat, and moisture when used with the supplied protective caps. The earset should always have a protective cap in place to keep sweat, makeup, and other foreign material out of the microphone.

The E6 earset's flexible boom is easily shaped right on the performer's face. Changeable protective caps let you shape the frequency response for different situations or to match other microphones. This omnidirectional version includes three protective caps—+4 dB (bright), +8 dB (very bright) and +0 dB (flat)—that controls the amount of crispness or sibilance (response at 15 kHz.)

Easy adjustment keeps the mic in a comfortable position for rejecting unwanted sounds. The omnidirectional E6 earset provides more isolation and is suitable for situations where there are loud monitors, extreme feedback, or environmental noise.

The included removable, quick-swap cable detaches from the actual earset, making it completely replaceable in the event of a short or break. The replaceable cable design makes upgrading wireless microphone systems easy as they are available in a wide selection of connections to accommodate most wireless transmitters.

Related Questions and Answers

Q: 1. Does this work with and it is essential if I want to connect my TASCAM DR-05 to my Canon 7D?

A: In order to connect the output of Your Tascam recorder to the mic input of a DSLR, you will need an attenuator cable such as this Sescom cable. It will allow the camera to receive a safe audio level, and retain headphone monitoring.

Q: 2. Do we really need it with the Zoom H6 as I have read that you can bring down the Levels in H6 upto -35db? I will be using the H6 with Canon 5D Mark 4

A: The H6 may have that feature, but I would still recommend this cable for your setup, as lowering the sensitivity that much would raise the noise floor on the recording.

Q: 3. Hello, on the rear panel of the device is mentioned that power supply is 120V AC 50/60Hz but in Europe supply is 220V AC 60Hz.Can we connect this device on European power supply? Usually product that comes from USA have both 110/220V AC power supply.Thank you

A: this device has not have a switch to 220V, so i do not recomend that you connect it to a 220V.

Q: 4. This attenuator cable is -25 dB. Other cables are -35dB. What cable is more suitable for Tascam DR40, 40X ?

A: If using this to connect a DR40 into a camera, the -25db cable would be fine to ensure a strong enough level into the preamp of the camera while not overloading it.

Q: 5. What is the warranty? I have one a few years old and it's starting to have buzz issues.

A: Rolls rack mixers are covered by a limited one year warranty for parts and labor from the Manufacturer.

Q: 6. Can I use this cable to connect my H4N Zoom directly into my Panasonic GH4 and have the audio sync with video? Also will the headphone connection monitor the audio of the zoom or the camera? Thanks!

A: That's pretty much what it is designed to do. It takes the headphone level output from the headphone jack of your H4N and splits it into two ends, one mic-level output (male 3.5mm) that you can plug into your camera and one headphone-level output (female 3.5mm) that you can plug in headphones to monitor. BTW, my next suggestion is not what you asked about or how the product was designed, but I prefer to have a separate sound operator who records the sound on my Zoom H4N and transmits the mic level signal over a wireless pack to my camera. In this scenario, my sound operator uses this cable to monitor on headphones from the Zoom H4N while also plugged into a lav mic transmitter.

Q: 7. why do I get a hissing sound while using this cord with my h4n zoom and 5d mark ii? I'm guessing its best to set the interior audio setting to manual.

A: Hi Tisa,Yes, it is best to have the on-board audio set to manual with this cable. You may need to do a few test recordings to get the settings properly dialed in.

Q: 8. Is this compatible with android devices?

A: You can use the Kopul ACH4-25MON with an Android device but you will need to use it with a 3.5mm TRRS adapter to convert the plug from 3.5mm TRS to TRRS since smartphones have a 3.5mm TRRS connector. The Rode SC4 3.5mm TRS Female to 3.5mm Right-Angle TRRS Male Adapter Cable for Smartphones (B&H # ROSC4). Another option would be to use a similar cable that already has a TRRS connector such as the Movo Photo TCB2 XLR Female Microphone to 3.5mm TRRS Male Smartphone Adapter (B&H # MOTCB2) or the MXL Female XLR to 3.5mm Male TRRS and 3.5mm Female TRS Multimedia Adapter Cable (B&H # MXMMCABLE1).

Q: 9. Is this cable absolutely necessary if connecting the Zoom H6 to the mic input on a Canon EOS SL3 DSLR ?

A: Yes you will need an attenuating cable to adjust the outgoing line level audio signal to the microphone level required by the camera.

Q: 10. This attenuator cable is -25 dB. Other cables are -35dB. What cable is more suitable for Tascam DR40, DR40X ?

A: If using this to connect a DR40 into a camera, the -25db cable would be fine to ensure a strong enough level into the preamp of the camera while not overloading it.