This Tensioned Large Advantage Deluxe Electrol 16:10 Wide Format Motorized Projection Screen from Da-Lite has a 120.0 x 192.0" viewing area with a Cinema Vision HC flame retardant and mildew-resistant finish.

High Contrast Cinema Vision has a 1.1 Gain rating and 50° (L/R) viewing angle. It is designed for use with DLP and LCD video projectors. It is suitable for venues where you have some control of ambient light. Its gray base and high reflectivity rating delivers good black levels without any negative effect on the white levels. If the finish becomes soiled, it can be cleaned with mild soap and water. Tensioning on each side of the seamless fabric assures a flat, undistorted surface that eliminates any chance of a skewed image. This finish comes with black backing for opacity and standard black masking borders.

One of the major advantages of this screen is that the fabric roller can either be factory installed or at your chosen location after the ceiling recessed, UL Plenum rated extruded aluminum white housing has been roughed in. The enables you to finish the initial installation but choose your screen finish at a later date. It should be noted that this version of the screen has a wider casing to accommodate a larger roller.

The screen includes two motors; one for the ceiling door and one for the fabric. The interior roller features a quick reversal motor, oiled for life, with automatic thermal overload cutout, integral gears, capacitor, and an electric brake to prevent coasting when the screen is stopped at a chosen length. The built-in Low Voltage Control controls up/down and stop functions using the included 12VDC three-position switch that can be wall mounted where convenient. It can also be operated from an optional radio frequency, infrared or auxiliary transmitter.

Ceiling Recessed    226" Diagonal    16:10 Aspect Ratio    Install Case First, Roller at Later Date    Built-in Low Voltage Control    Front Projection

Related Questions and Answers

Q: 1. 8 X 10 Matted work - will it fit within this fame. Need to retain mat signed by artist? Yes question, thanks. Won't fit in Frames I've tried in stores

A: you don't have much room here. if your matt is thicker than what we usually see then it will not fit. I believe a Framatic frame has a very similar look plust far more room for a thicker mat.

Q: 2. What software is recommended to stitch the images together?

A: I have used Adobe Lightroom and also PTGui software to stitch the photos together.

Q: 3. Can this be used for a Ultra Short Throw projector?

A: Yes, this screen can be used with an ultra short throw projector, to make a 120- inch diagonal image.

Q: 4. Will this mount work on the crown graflex 4x5?

A: If you have a Graflok back, you can use this on your Crown Graflex 4 x 5.

Q: 5. How does this screen mount on the wall?

A: Design and Installation Aluminum lightweight split-frame design Screen stretches over frame for a tensioned, flat surface Designed to assemble and install in minutes Smaller footprint with thin bezel maximizes viewing area EDGE FREE or install ultra-thin velvet tape trim Wall mount brackets slide ensuring the frame is properly centered Optional LED backlight kit with remote control (available separately) Optional splice bracket kit (available separately) connects multiple frames to create a large size display

Q: 6. Will this work with an ultra short throw projector?

A: Yes, keep in mind this is meant to reject light coming from the ceiling.

Q: 7. Can this screen be hanged from the ceiling?

A: It is not made to hang from a ceiling. It is made for wall hanging only.

Q: 8. did you have for Sinnar??

A: If your sinar has a graflex back then it will fit. My old sinar did. Realize that if you are using a Nikon dslr that has a mirror you will not be able to slide the Nikon very far from center. This is because the distance between the sensor and the front of the camera where the lens would normally mount is too far and the edges will cast a shadow. That space is taken up by the mirror movement and is Calle the mirror box That's the problem I had with this adapter. It's well built but I could only use it near the center of the 4x5 area with my D800E. It should work fine with a mirrorless DSLR like th Sony alpha7 assuming you have the correct adaptor.

Q: 9. Estimated time to build and install this screen?

A: Every installation is differnt but the screen should assemble in well under an hour. Wall mounting times may vary with experience.

Q: 10. Can I put in wall speakers behind this screen?

A: This screen is not designed as one of those perforated screens for sound. I have not put speakers behind it but if you are wanting to do that for convenience its sound transparency is not bad. If you are a true audiophile wanting the most optimized sound then this screen is NOT designed or ideal for this purpose.