Connect your DJ and professional audio equipment with virtually no electrical interference with the 3' Mogami Gold Male XLR to RCA Cable. Its spiral shield with stranded copper helps prevent interference from other nearby equipment.

Spiral Shield with Stranded Copper

• Ultrahigh-Density Spiral Shield with stranded copper so precisely wound that one layer achieves 100% coverage
• Extremely low-loss and neutral cable with dead silent background
• Suitable for DJs setting up in unpredictable electrical environments

Related Questions and Answers

Q: 1. Which connector carries audio to the headphones and which is the microphone? Trying to see if there would be an aviation plug

A: In the Shure 3-Pin XLR Male and 1/4" TRS Male to BCASCA Cable; The XLR end is for the microphone and the 1/4'' TRS end is for the headphones.

Q: 2. Will this work the Synco D2 shotgun microphone (needs phantom) plugged into a passive Beachtek audio adapter?

A: No, the Deity Microphones V-Link 3.5mm TRS Male to XLR 3-Pin Male Microphone Adapter Cable will not work with the Synco Mic-D2 Hypercardioid Shotgun Microphone because it has a male XLR connector and the mic requires a female XLR connector. The V-Link Adapter Cable is intended for use with a microphone that has a 3.5mm output and requires plug-in power, but needs to connect to an XLR input. This cable does not allow phantom power to pass through to the microphone. It has a built-in phantom power converter that converts phantom power to 3 to 5V of plug-in power. The Mic-D2 needs to connect to an XLR mic input that can supply 48V of phantom power for the mic to operate.

Q: 3. Is it possible to use this for DMX 5-Pin transmission to fixtures that have TRRS connections?

A: The Senal SMH-H5X2 2.5mm TRRS to 5-Pin XLR Male Cable for Communication Headsets does not have the correct wiring to be used with DMX fixtures; it is for use with audio devices only.

Q: 4. Will this connect a Sennheiser EW G3/G4 RX to a MixPre's XLR input? If so, is it 100 (unbalanced) or 500 (balanced) wiring?

A: No, the Deity Microphones V-Link 3.5mm TRS Male to XLR 3-Pin Male Microphone Adapter Cable is not compatible for connection to a Sennheiser receiver. For a similar cable that is compatible for use with a Sennheiser wireless receiver, you can use the Cable Techniques Right-Angle Locking 3.5mm TRS to Low-Profile XLR Male Coiled Cable for Sennheiser (B&H # CACCG4X3M8) or the Sennheiser CL 35-XLR Right-Angle Locking 3.5mm TRS to XLR Male Coiled Output Cable (B&H # SE700062).

Q: 5. Are there replacements for the non ear piece cushion?

A: There are currently no replacements available for the small cushion on the Senal SMH-1010CH Single-Sided Communication Headset with 5-Pin XLRM Cable for Telex System.

Q: 6. Does this provide phantom power like the Deity Microphones D-XLR 3.5mm to XLR Adapter with Phantom to Plug-In Power Conversion BH #DEDXLR? I want to use my Deity Microphones V-Mic D3 Pro into a Focusrite Scarlett Solo interface to stream on Twitch with. Would this work?

A: Yes, the Deity Microphones V-Link 3.5mm TRS Male to XLR 3-Pin Male Microphone Adapter Cable can be used for the same types of applications as the Deity Microphones D-XLR 3.5mm to XLR Adapter with Phantom to Plug-In Power Conversion. Like the D-XLR Adapter, the V-Link Cable has a built-in power converter that will allow you to use phantom power (48V) from the XLR input on the Focusrite Scarlett Solo USB Audio Interface and then converts it to plug-in power (3 to 5V), which the Deity Microphones V-Mic D3 Pro Shotgun Microphone requires to function.

Q: 7. Will this connect properly with good audio quality from the RodeLink Receiver/Rode Wireless Go's Receiver to a camera's XLR input?

A: It works for me

Q: 8. Which 3.5mm contact is connected to the RCA center pin?

A: The center pin of the Calrad Electronics 35-512 Stereo 3.5mm TRS Male to RCA Female Adapter is positive as well as the pin on an RCA plug.

Q: 9. Second question: Will this also work with the Synco D2 when plugged into the new Beachtek-Max Active Audio Adapter DSLR?

A: No, the Deity Microphones V-Link 3.5mm TRS Male to XLR 3-Pin Male Microphone Adapter Cable will not work with the Synco Mic-D2 Hypercardioid Shotgun Microphone because it has a male XLR connector and the mic requires a female XLR connector. The V-Link Adapter Cable is intended for use with a microphone that has a 3.5mm output and requires plug-in power, but needs to connect to an XLR input. This cable does not allow phantom power to pass through to the microphone. It has a built-in phantom power converter that converts phantom power to 3 to 5V of plug-in power. The Mic-D2 needs to connect to an XLR mic input that can supply 48V of phantom power for the mic to operate.

Q: 10. Does it work with rode wireless go 2?

A: Yes this works with the Rode Go II