From Camplex, the Premium Bend Tolerant Single Mode Duplex LC to LC Armored Fiber Patch Cable, 3.3' long and in yellow, is a riser-rated cable with stainless steel wrapped fibers. Moisture-, crush-, rodent-resistant, and flame-retardant, it's highly suitable for applications such as high-speed network patching located in changeable indoor environments. The cable also features ceramic ferrules for long-lasting reliability and precision alignment.

Riser-Rated    Stainless Steel Wrapped Fibers    Moisture, Crush & Rodent-Resistant    Flame-Retardant

Related Questions and Answers

Q: 1. Has Canon changed the LC-E6 battery charger with the introduction of the new LP-E6N battery?Discussion: I purchased a Canon 60D about 3 years ago that came with the LP-E6 battery. I very recently purchased a Canon 7D Mark II that came with the new LP-E6N battery. Each came with a LC-E6 charger. However, the writing on the back is slightly different between the two chargers and the charger that came with the 60D weighs 4.5 ounces where the one that came with the 7D Mk II weighs less at 4 ounces. Hence, these two battery chargers are not exactly the same. Form, fit & function maybe, but something is different.

A: I wish I could say I can verify... but am not confident that my answer would be correct. I hope someone else responds to assist you!

Q: 2. Does the cap come with the small strap to attach to the camera?

A: No, the Nikon LC-CP31 Lens Cap for COOLPIX L840 and B500 does not come with any strap or tether to keep it connected to the camera when taken off the lens. We do have the Sensei Cap Keeper Lens Cap Holder that will work for this, BH #SECKL (https://bhpho.to/3rwjzo8). One end goes around the lens barrel, and the other end attaches to the lens cap via the adhesive-backed disc.

Q: 3. CAN YOU USE THIS LENS CAP TO COVER A NIKON HN-3 LENS HOOD ? OR DO YOU NEED TO USE THE 67 MM SIZE MODEL ?

A: The LC-52B cannot work along with the Nikon HN-3 Lens Hood, being that this hood screws into the filter threads of select Nikon lenses.

Q: 4. Will this work with the BP-808 batteries ?

A: No, it wont. Use: https://a href= http://www.bhphotovideo.com/c/product/836071-REG/watson_c_1508_compact_charger_f_canon_bp808_bp809.html/pageID/accessory target= _blank www.bhphotovideo.com/c/product/836071-REG/watson_c_1508_compact_charger_f_canon_bp808_bp809.html/pageID/accessory/a

Q: 5. will this cap fit a Nikon L840?

A: Yes. I bought one for my 840

Q: 6. Is it comaptible for the canon sL1 too?

A: The Canon SL1 uses a different battery than this charger supports. You will need the Canon LC-E12.

Q: 7. Does this charger work for LP-E6N for Canon 80D? My camera bag was stolen with my charger inside. Camera is worthless without a battery charger.

A: Thank you!

Q: 8. Is there a replacable cord for this that uses USB instead of a wall outlet?

A: No

Q: 9. What's the charge time for a pretty dead battery to 100% charge? (as in, how long does it take to charge a battery?)

A: I would estimate 1.5 hours to a full charge.

Q: 10. I'm assuming it also charges the T3i (not listed)...Also, is it ok to leave the battery in the charger when it is unplugged, or will that drain the battery over time?

A: It will also charge the T3i. Generally you want to remove the battery from the charger when it is not unplugged. Leaving the battery in the charger unplugged for short periods of time usually isn't a problem however.