Support a heavy lens while using an LPL lens adapter using this 15mm Rod Clamp for LPL Adapters from Vocas. The aluminum rod clamp fits around your Vocas LPL lens adapter and the standard 15mm rod clamp attaches to separately available top-mounted rods. The clamp is height adjustable to fit a variety of camera setups.

Mount LPL Lens Adapter on 15mm Rods    For Top-Mounted Rods    Height Adjustable, Fits Around Adapter    Durable Aluminum Construction

Vocas LPL lens adapters

Related Questions and Answers

Q: 1. what is the min/max filter thickness that will work with this matte box?

A: This matte box will work with any 4 x 5.65" sized filter. The standard for such a filter is 4mm thick.

Q: 2. What is the widest focal length lens that can be used with super35mm format? How much does this MB weigh?

A: Generally speaking, matte boxes will accept 18mm and above in Super35 and 24mm and above in Full Frame. Specific combinations of wider lenses, camera and matte box would have to be tested.

Q: 3. I'm using a Sony FS7 with the Zeiss LWZ.3 21-100mm. How can i adjust the mattebox on the rod to make sure it will fit my front lens (114mm). I don't see anything to adjust the heigh of the mattebox?

A: The MM4 mattebox does not have a height adjustment. With the correct step down ring (130mm to 114mm MOV-301-02-004-108C), the mattebox can clamp directly onto the front of the lens. Using the Movcam FS7 / FS7 II baseplate and riser would allow for cinema standard height alignment if you choose to go a different route for your camera support.

Q: 4. Is this Matte Box wide enough to cover a FF sensor with a 14mm FF lens? For example a Sony a7S with a Xeen 14mm, will it vignette?

A: Yes, it's wide enough. I use it with an URSA Mini 4.6k and the Xeens, including the 14mm, with no problems. The URSA Mini camera isn't full frame, but I still think you'll be fine. You'll need to make sure you have a baseplate that raises the A7s up quite a bit. The matte box is adjustable vertically, but there is a minimum height that the camera lens needs to be at

Q: 5. Can I use this matte box on the seen cine lenses?

A: Yes, this Matte box will work with Cine lenses that have a 114mm front diameter or smaller (with adapters). This kit "includes six step-down rings (52-82mm, 58-82mm, 62-82mm, 67-82mm, 72-82mm, and 77-82mm)"

Q: 6. Is there a 4x4 filter holder that works with this mattebox?

A: The unit comes with combination 4x4/4x5.650 filter holder. However if you want 4x4 only then you will need item 301-0201-13

Q: 7. I don't see how this works. There is no description. How does this attach?

A: This part replaces the handgrip that is included with the C300 Mark II. This 2nd picture on our website shows how it is attached to the C300 Mark II.http://bit.ly/2cu1aAQ

Q: 8. This came up when I set rod support to "15mm LWS". Is that correct or is this standard studio rod distance?

A: That is correct, this system is 15mm LWS.

Q: 9. It works with VCT Universal Baseplate (zacuto)? Thanks.

A: Yes. I use it with Zacuto's Universal Baseplate and it works great. If you're using shorter lenses, such as CP.2s, CN-Es, Xeens or Rokinon Cine DSs, you may need to buy some shorter 3.5 15mm rods so that you can lower the bottom of the matte box below the rods. This allows you to center the matte box on the lens. I use this setup with a URSA Mini 4.6k, but if you are using a taller camera such as a RED, which has a higher lens mount, you may be OK.

Q: 10. How much do each of the components weigh? I see that the overall weight is listed as 2.35 lbs, but it's not clear what is included in this weight.

A: Hello Tony! Thank you for your question! You can visit our website directly for this information. Essentially, the mattebox itself is roughly 1.20 lbs, and then the total of accessories are about between 0.05, 0.10 lbs each, reaching a total of 2.35 lbs.a href= http://www.shapewlb.com/en/product/products/accessories/matte-box/matte-box-4x56_939.aspx?id_page_parent=385 target= _blank http://www.shapewlb.com/en/product/products/accessories/matte-box/matte-box-4x56_939.aspx?id_page_parent=385/aPlease take note that this mattebox is sold by SHAPE, not manufactured by SHAPE.We hope this helps and we thank you for your interest in our products.The SHAPE team