The light beige E2 Unidirectional Earset Microphone with Detachable Cable and Hirose 4-Pin AT cH-Style Connector from Countryman is an over-the-ear earset, similar to a classic E6 earset, but with a shorter boom designed to work with Audio-Technica wireless microphone systems. It provides suitable isolation at the mouth, but with less visibility than an E6 omni earset, and can be used to capture audio for loud speaking and vocal applications.

With an equalizing circuit built into the audio connector, the frequency response is tuned so you can experience full-bodied bass and precise highs that are warm and natural. The element, boom, and sub-miniature connector are all easily hidden on the user's face. The boom position near the ear helps to eliminate breath pops and vocal plosives on the mic. The detachable cable terminates to a Hirose 4-pin AT cH-Style connector for direct connection to an Audio-Technica 1100 Series, 200 Series, 2000 Series or 3000 Series bodypack transmitter (sold separately).

For Audio-Technica Wireless Transmitters    20 Hz to 20 kHz Frequency Response    For Loud Speaking and Vocals    Fits over the Ear    Includes Carrying Case    Black and White Cable Clips    Windscreen and Protective Cap

The E2 Earset redefines pure sound in a virtually invisible package. It offers better ease of use than a lavalier or podium microphone.

There are two aspects of the E2 design that make it possible to capture sound so far away from the mouth: strong off-axis rejection and precisely tuned frequency response. For on-axis interference, the frequency response tuning in the connector of the E2 allows you to fully capitalize on the proximity boosting effect of the mic to achieve even stronger isolation in the voice band.

Like the connector for the industry-standard E6, the connector for the E2 is built tougher and more water resistant than previous models.

Lower gain, for powerful vocals requiring the highest overload.

Related Questions and Answers

Q: 1. Does this come with a 1/4-20 bolt? It says it "Requires 3/8"-16 or 1/4"-20 Bolt". But I specifically need the latter.

A: 1/4"-20 and 3/8"-16 bolts are not included with the Kondor Blue ARRI-Style 3/8"-16 Pin to 15mm Rod Clamp (Raven Black), however if you have a 1/4"-20 bolt to use with the clamp it will support the 1/4"-20 bolt as a mounting method. The bold will go through the clamp and come out the end with the anti-twist pins. Then a 15mm rod would enter the open end on the opposite side where it would then be clamped into place.

Q: 2. How does this strap work when shooting in portrait orientation?

A: Works totally fine in vertical orientation.

Q: 3. What is this strap made out of?

A: This strap is made of nylon; the top of the padded section is synthetic leather.

Q: 4. What is the load capacity?

A: The O.C. White ProBoom Elite Microphone Arm System can support up to 2.5 lbs.

Q: 5. Can this be used with a tripod?

A: I tried it with my Slik Af-2100

Q: 6. Will this work with a Nikon Camera?

A: Yes it will work it will be a little funky with the triangle attachments for the straps

Q: 7. Can this be used while the neck strap is still attached?

A: You could use the Canon Hand Strap E2 on most cameras when most neck straps are attached.

Q: 8. What is the "length" of the padded section of the Hand Strap?

A: The length of the padded section is 4.75" at its longest and it is about 2" wide at its widest.

Q: 9. Will this hand strap work on my 1DX Mark II?Thanks!

A: Yes. I is a bit expensive, but it is worthed. I had previously tried a generic version and the quality was pretty bad. Ended getting this one, which will work on any Canon full frame camera and many other brands and models too.

Q: 10. Does this have the ability to be used on an R5/BGR-10 combo WITHOUT using the tripod socket?

A: As the Canon BG-R10 Battery Grip has a strap lug on the bottom of the battery grip, yes, you may connect the Canon Hand Strap E2 to the Canon BG-R10 Battery Grip without using the tripod socket on the bottom of the battery grip.