With built-in ergonomic shoulder pad, 10" sliding track, extra space for accessories in front, VCT14-compatible V-wedge, red buttons and levers all around, and much more, this is the stylish VCT Pro Baseplate from Zacuto. Use it with all types of cameras, from DSLRs to larger models, like the Alexa.

A section of the baseplate extends out beyond the 15mm LWS rod adapter in front. With the rod adapter thus set back, you have additional space to mount accessories under the camera lens, allowing you to position the camera further back on the plate, keeping the balance point of your rig directly over your shoulder. (The rod adapter is vertically adjustable 1", and has to be in a raised position to allow for accessories to be mounted in the additional space. Also, a 1.8" riser for the rod adapter is optionally available for RED cameras by special order from Zacuto.) Also, on the bottom of the section that protrudes out is where the V-wedge is. There is also a 15mm LWS rod adapter on the rear.

The VCT Pro Baseplate features a 10" sliding track, providing the space to optimally adjust balance after every lens change. Moreover, the included red camera plate can be loosened by a spring-loaded lever instead of a screw, so you can make adjustments quickly and easily. To fully release and remove the plate (and camera), just press a red button on the side of the baseplate and slide the plate out. The rod ports also have spring-loaded levers.

An ARRI M6 rosette is available on the front for attaching accessories and grips, and there are also three 1/4"-20 threaded holes on the side providing additional mounting options. 1/4"-20 and 3/8"-16 tripod mount holes are available on the bottom to use instead of the V-wedge. The shoulder pad runs pretty much along the entire length as well as width of the baseplate, and is made of gel polymer. Two 6.5" 15mm rods are included. One 1/4"-20 and one 3/8"-16 screw are supplied for the camera plate. The VCT Pro Baseplate is made in the USA.

For Canon C500 Mark II & C300 Mark III    VCT Pro Baseplate with Shoulder Pad    Top Plate with Z-Rail & LCD Mount    Rosette Trigger Grip & Recoil Handle    Trigger Cable for Handgrip

• Front rod adapter is set far back, providing more space for accessories, and allowing the camera to be positioned further back for better balance
• 10" sliding track (with spring-loaded lever) for balance adjustment after lens changes
• VCT14-compatible V-wedge
• 1/4"-20 and 3/8"-16 tripod mount holes
• Ergonomic gel polymer shoulder pad
• 15mm LWS rod adapter on the rear
• Front rod adapter is vertically adjustable 1"; optional 1.8" riser available from Zacuto for RED cameras
• ARRI M6 rosette
• Three 1/4"-20 threaded holes for accessories
• Includes two 6.5" 15mm rods
• 1/4"-20 and 3/8"-16 screws supplied
• Made in the USA

Related Questions and Answers

Q: 1. Is there a reason this only comes with only one handle, and why the left side (especially if you are focusing with your left hand)? The display in the store, had both handles attached.

A: The second arm is not included with the Shape kit to offer you a choice on which arm solution you would like to work with. The options are - A duplicate arm BH #SHHAND2S or BH #SHC52RH - SHAPE Remote Extension Handle with Cable for Canon C500 Mark II and C300 Mark III.

Q: 2. Are the side parts of the cage system required to use this top plate, or does the top plate mount to the camera? I wish to use the top plate, handle and monitor mount without the rest of the cage components.

A: You can use the SHAPE Top Plate for Canon C500 Mark II and C300 Mark III as a stand alone item. It does not require other parts to mount to your camera. Part number for the Shape top handle is B&H # SHLPHT

Q: 3. Will this work (compatible) on the new Canon C400?

A: Since the Canon C400 is a newly announced product, we do not currently have compatibility information with the Wooden Camera Battery Slide for C300 Mark III and C500 Mark II (V-Mount). The 4 Pin XLR power cable would be compatible, but the mounts to the camera may not be the same distance for proper compatibility.

Q: 4. Will this work with the original C500?

A: If the screen size is 4.3", like the Canon LM-V2 4.3" LCD Monitor, then yes, the Zacuto Canon C500 Mark II & C300 Mark III Z-Finder will work with the original C500.

Q: 5. Description says it sits at an angle. That makes sense for hot swapping, but can it also sit flush against the back of the camera? That's what I'm looking for for hand held. An angled battery would be just as uncomfortable as the stupid canon battery design as it is.

A: Using a BP-A30 battery will allow the Wooden Camera Battery Slide to sit flush to the camera.

Q: 6. Is this compatible with the C300 Miii?

A: The SHAPE Camera Cage for Canon C500 Mark II and C300 Mark III is compatible with the C300 Mark III.

Q: 7. can I use the original top handle with this plate or do I need a new handle?

A: Yes, the SHAPE Top Plate for Canon C500 Mark II and C300 Mark III can accommodate the Canon C500 Mark II and C300 Mark III handles.

Q: 8. Is the top handle included?

A: The top handle is included in this kit.

Q: 9. Does this rig include the electronic cable that connects the camera body with the Canon hand grip?

A: Yes this product will come with the cable to connect the trigger grip to the camera.

Q: 10. Can I use this plate to attach to a Ronin 2?

A: This plate is designed to attach to the top of the Canon C500 II, C300mk III, and it should work with the Ronin 2 gimbal.