Enjoy enhanced stereo sound with your favorite pair of speakers and the silver Audiolab 6000A Stereo 100W Integrated Amplifier. It outputs up to 50W per channel at 8 ohms and features Bluetooth connectivity in addition to its two digital coaxial, two optical, and five stereo RCA inputs. One RCA input is a dedicated phono input and is accompanied by a ground screw terminal. An 1/8" headphone jack with discrete amplification enables private listening. The 6000A includes a remote control as an added convenience.

2-Channel Amplifier Configuration    50W per Channel Power Output @ 8 ohms    ESS SABRE ES9018K2M DAC    Bluetooth Audio Input    2x Digital Coaxial, 2x Optical Inputs    5x Stereo RCA Inputs with Phono    Stereo RCA Output    Includes Remote Control

The onboard DAC lets the 6000A play digital sources without the need for an external DAC or other additional component. The 6000A uses the ES9018 SABRE32 Reference chip family for its D/A conversion, utilizing ESS Technology's 32-bit HyperStream architecture and Time Domain Jitter Eliminator to deliver low noise and high dynamic range. The amplifier has four digital inputs, three line-level analog inputs, a dedicated turntable input, Bluetooth wireless connectivity, and a dedicated headphone amplifier in addition to the speaker amplifiers.

The discrete Class-AB power amp stage in the 6000A delivers 50W per channel into 8 ohms with a maximum current delivery of 9A into difficult loads. Its output stage uses a CFB (Complementary Feedback) topology to help ensure enhanced linearity and thermal stability, as the idle current is kept independent of the temperature of the output transistors. A 200VA toroidal transformer, followed by four 15,000 μF reservoir capacity, helps the amp maintain control of the music while enabling a wide dynamic range.

The preamp section is kept simple to help maintain signal purity, with line input signals passing to the analog volume stage, which covers the range from -80 dB to 8 dB in steps of 2 dB and 1 dB; step resolution increases with volume position. The physical layout of the 6000A's circuitry is engineered to protect the preamp section from noise interference.

Related Questions and Answers

Q: 1. Does this unit work with both 110 volts and 220 volts?

A: Yes, this Audiolab 6000A Stereo 100W Integrated Amplifier works at 100 to 240 VAC, 50 / 60 Hz - allowing it to work with power in any region.

Q: 2. I want to connect four 6 ohm speakers to the yamaha a s501 amp and use at the same time.Do I set impedence switch on back of amp to high or low ?

A: Set to low.

Q: 3. How sensitive is the remote volume control at lower levels? My Denon PMA-600NE jumps too much from the lowest settings.

A: The loudness control will provide up to -30dB of attenuation of the Yamaha A-S301 Stereo Integrated Amplifier (Black), BH # YAAS301BL. If the volume is too low, turn down the volume, set the LOUDNESS control to the FLAT position, and then adjust the VOLUME again. The volume control functions in measured steps, either from the remote control or the volume control knob on the body of the receiver.

Q: 4. I have an older Bose surround sound speaker system, 4 speakers, a tweeter, and a bass. Will this system work with this eq.?

A: The Yamaha A-S301 is a stereo amplifier for powering speakers and does not function as a standalone EQ.

Q: 5. Shall we equalize the sounds with low, medium and high frequencies?

A: The Audiolab 6000A does not have EQ controls.

Q: 6. Can the "line out" and "line in" connections be used to connect an equalizer?

A: The Line In and Out connections on the Onkyo A-9110 2-Channel 100W Integrated Amplifier (B&H # ONA9110) can be used with an equalizer, but for best results, it would be advisable to connect the equalizer to the output of your audio source device, then to the stereo input on this amplifier.

Q: 7. Is the RCA line out a preamp line out for a line in on a second power amp for a second set of speakers?

A: The Onkyo A-9110 2-Channel 100W Integrated Amplifier (BH # ONA9110) features a Line Out set of RCA jacks that will drive a pair of self-amplified/active speakers or for sending a line level signal to al line level device like an amplifier, or mixer.

Q: 8. how do i hook up a subwoofer to this amp, there is no sub-out?

A: The A1200SL is more meant for Music Audio Enthusiasts who are connecting to Higher end Audiophile Grade speakers. It is common among most Higher End Integrated Amplifiers to not include a Subwoofer connection. The Denon PMA-A110 for instance also does not provide a Subwoofer out.

Q: 9. Is POWER AMP IN the same as PRE OUT?

A: No. The Power Amp In is used when you connect an external preamp to the Marantz Model 40n so that you can use the Model 40n as a power amplifier.

Q: 10. Does this amp take Banana Plugs to hook up the speakers?

A: The Yamaha A-S301 Stereo Integrated Amplifier (Black) BH #YAAS301BL would accept banana plugs.