Run your BNC cables through the wall neatly with the gray Lexan My Custom Shop 5-BNC 2-Gang Wall Plate. It features five color-coded BNC connectors on each side, so you can run your cables through the wall for easy connection to your display or source device.

Double-Gang Design    5x BNC Ports on Front and Rear    Color-Coded Terminals

Related Questions and Answers

Q: 1. What is the size of the screw holes?

A: The scroll holes measure about 6mm.

Q: 2. I will be connecting (soldering) this wall mic to a mic cord and was wondering which wires are positive/negative and the same for microphone cable?

A: There are two wires on the back of the mic. The blue wire is positive (+) and the black wire is negative (-). Wiring instructions should be included with the microphone. For further information, you can reach technical support at Telex by phone at 800-898-6723.

Q: 3. What is the outside diameter of the receiver? Trying to determine if this could be used as a Junior Pin

A: If you remove the knob you could use it as a junior pin.

Q: 4. Can you remove some of the dividers or are they permanently affixed in place?

A: The dividers cannot be removed.

Q: 5. How much weight can these support? I want to use three of these to hang a 37-pound canvas backdrop on my wall (the backdrop is mounted on a top rail made of wood with three holes for hanging).

A: These are welded steel. The weak point will be the wall and how you anchor them.

Q: 6. Hi, I recently purchased from B&H the HLPP3M loupe and now want the base plate to suit my 800e ... Is this the correct one and will it work with and without the battery base on the camera? ..thanks Geoff (a wish I lived in New York customer so I could see all the goodies in the store)

A: Yes, the Hoodman HCP DSLR Camera Custom Finder Base would be compatible for use with the Nikon D800E DSLR camera both when using the camera with a battery grip or when used with the camera by itself.

Q: 7. How much is the load capacity?

A: This question cannot be answered without knowing the direction of the load and the orientation of the base to which the load is applied. Oriented where the contained rod is vertical and in compression, failure would occur in the rod. Oriented where the rod is vertical and in tension would result in the failure at the set screw where the rod is attached to the base where the rod is steel or in the rod if it is aluminum.Oriented where the rod is horizontal would result in a bent rod long before this base would fail if it is firmly attached to a wall. I think the screws holding the base would fail before the base. This base is steel and is not likely to fail.This base accepts a 16mm rod. I think even a steel rod would bend before this base would bend or a weld would break.This base accepts a 16mm rod.

Q: 8. What size Chromebooks fit in this? Some reviews say they don't actually fit, but I'm wondering if it's just because they only fit up to a certain size.

A: The divider spaces on these shelves are 1 wide. You have plenty of height and depth. As long as your Chromebook is .9 thick or less, and less than 12.9 x 12.1. Most Chromebooks fit with room to spare.

Q: 9. Will it mount to a Sony FX3?

A: Yes, the Hoodman HCP2 Mirrorless Camera Custom Finder Base Plate for HoodLoupe would work with the SONY FX3. Please note that this is just the mount, and it does not include the Hoodloupe. The best choice would be the 3.0" model but that is discontinued. Hoodman HoodLoupe Outdoor LCD Viewfinder for 3.2" Screens BH #HOH32MB • MFR #H32MB

Q: 10. Will this work with the Sony Fx3?

A: Yes, the Hoodman HCP DSLR Camera Custom Finder Base Plate for HoodLoupe can work with the FX3.