Add a high-capacity, professional Gold mount battery to your Canon C70 or C80 camera with this Battery Slide Pro from Wooden Camera. The slide mounts onto any Canon Accessory Mount by interlocking with the mount and securing the 1/4"-20 screw. It supports a single Gold mount battery that powers the camera via a DC barrel connector while leaving access to the camera's standard BP-U battery compartment, so hot swapping is supported.

The Battery Slide Pro also features three D-Tap ports for powering accessories, and its integrated digital fuse monitors the D-Tap ports and disables them if they exceed the set current for accessories while leaving the camera running. Once the load has been reduced by removing accessories or otherwise, a reset button can be pressed to enable accessory power again.

Once the Battery Slide Pro is attached, the battery plate position can be adjusted by loosening a lever and sliding the plate.

Attaches to Any Canon Accessory Mount    Supports 1 x Gold Mount Battery    Access to Camera Battery for Hot Swaps    3 x D-Tap Ports, Protective Digital Fuse    Powers Camera with DC Barrel Cable

Canon C70 and C80 cameras

Also compatible with but not limited to:
Wooden Camera Top Plate for Canon C70 (288200)
Wooden Camera Mini Top Handle for Canon C70 (282700)
Wooden Camera Top Plate for Canon C80 (A00834)
Wooden Camera Arca Riser Plate for Canon C80 (A00828)

Related Questions and Answers

Q: 1. What voltage is provided to the camera? In a number, please. Not just "the correct voltage".

A: The regulated voltage output of the Wooden Camera Battery Slide Pro for Canon C70 (Gold Mount) is 19.5 volts.

Q: 2. Can this be used to power other cameras such as c300 mk iii with the correct d-tap cable?

A: No, specific plate comes with the connects for the Blackmagic Pocket Cinema Camera 6K Pro. If you want to use a gold mount plate for the Canon C300 mk iii you will need this: BH #WO282200

Q: 3. Does it come with the cable to plug to the camera?

A: Yes, the cable is included.

Q: 4. Would this fit on the RED V-Raptor?

A: Yes, The Wooden Camera Pro V-Mount to Gold Mount Battery Adapter would be compatible and work with the RED V-Raptor.

Q: 5. When the V-mount battery dies during a take, the power sauce will be swapped to the BP-U battery seamlessly if it's in place?

A: The Wooden Camera Battery Slide Pro for Sony FX6 (V-Mount) acts as an AC adapter when in use and you cannot use BP-U batteries to hot-swap. For hot-swapping VMount batteries a sharkfin adapter is your best option.

Q: 6. Is there a (technical) reason this wouldn't work with cameras other than a Pocket 6K Pro if you have the appropriate Dtap cable?

A: The Micro Battery Slide Pro (Blackmagic Pocket Cinema Camera 4K / 6K / 6K G2 / 6K Pro, Gold Mount) comes with a Power cable that would only work with the cameras listed from Black Magic. However if you don't use the power cable is should work with any other camera model if you use the D-Tap connector that is located on most Gold mount Batteries. The Battery slider pro also has 2 D-Tap connectors on the mount. Please note you would need 15mm rods to mount it.

Q: 7. Weight of this please?

A: This should weight right around 1 pound.

Q: 8. Is the same one that came out for the Sony Fs7?

A: No, the Battery Slide Pro V-Mount is designed and made for the (Sony FX9) only.

Q: 9. Would this work with the BS1H full frame version of the camera? Or are they different power requirements? Thanks.

A: Yes, the Wooden Camera Micro Battery Slide Pro for Panasonic BGH1 will also support the full frame BS1H Cinema camera as well.

Q: 10. Will this also work with FX9?

A: No, the Wooden Camera Battery Slide Pro for Sony FX6 (V-Mount) does not have the appropriate mounting for the Sony PXW-FX9 XDCAM 6K Full-Frame Camera System (Body Only). The Wooden Camera Battery Slide Pro V-Mount for Sony FX9 is an appropriate plate. See the link below: https://bhpho.to/2DHqzEt