The waterproof, dustproof, and crushproof red 905 Hard Case with Foam from Nanuk is made from lightweight NK-7 polypropylene resin that protects and stores delicate compact gear like a camera, hard drives, binoculars, batteries, lenses, phones, or audio equipment. This version of the 905 is offered with a multilayer cubed foam insert in the 9.4 x 7.4 x 5.5" interior that makes it easy to customize to your specific needs or gear. For complete protection, the insert includes a convoluted eggcrate foam lid insert and a solid base layer for the bottom.

Its molded-in bezel and gasket are held fast with two PowerClaw latches. This patented latch uses compressive force to tightly clamp the case shut to a waterproof and dustproof IP67 rating, with an integrated slide lock that prevents the case from opening during transport or if dropped. For additional security, there are two 0.3" diameter padlock holes integrated into the case and lid. The case features a built-in pressure relief valve that regulates the internal pressure, keeping your gear and the case from getting crushed during air travel and allowing you to open the case without having to break a tough pressurized seal that may develop. Further design features include an integrated lid stay that prevents the lid from closing on your hand, rustproof and strong stainless steel hardware, and a foldable soft-grip handle at the top. This case can be stacked with other Nanuk 905 cases for your convenience.

Waterproof, Crushproof, and Dustproof    Lightweight NK-7 Polypropylene Resin    Customizable Cubed Foam Insert    2 PowerClaw Latches    Automatic Pressure-Release Valve    Molded-In Bezel System and Padlock Holes    Integrated Lid Stay for Safe Access    Comfortable Soft-Grip Handle    Stackable with Same-Size Cases

Related Questions and Answers

Q: 1. can I purchase the foam separately? Thanks!

A: Yes you can, they are available in the accessories page.

Q: 2. Are the leather attachment points now made out of plastic?

A: Unfortunately, Nanuk does not disclose what material the attachment points are made of for the Nanuk Shoulder Strap for NANUK 905 - 945 Cases.

Q: 3. Length?.

A: Hi Mate , from its fully adjustable length it is from centre of the clip to centre of the clip about 49 inches

Q: 4. Carry-on size for most airlines?

A: No, the Nanuk 940 Pro Photo Kit does not meet carry on regulations.

Q: 5. Would it work with DJi RS4 ?

A: Considering the slight differences in design of the gimbals, the Nanuk Waterproof Hard Case with Custom-Cut Foam Insert for DJI RS 3 and RS 3 Pro Combo (Silver) may not fit the DJI RS 4 Gimbal Stabilizer well. We would recommend the Nanuk 930 Hard Case with Foam Insert for DJI RS 4/RS 4 Pro Combo (Silver, 26.5L), BH #NA930S080SV, for the best fit.

Q: 6. What is the shortest length this strap can go?

A: The shortest length of the Nanuk Shoulder Strap for NANUK Cases is 32 inches.

Q: 7. Will the cards in there plastic cases still fit in the cards slots?

A: You have to remove the SD cards from the plastic cases to fit them in the slots on the Elephant Elite 26 SD Waterproof Hard Memory Card Case (Black Case /Black Foam).

Q: 8. Is it safe to store memory cards in a case with foam slots without their plastic cases?

A: Yes, the foam protects the cards as well or better than the plastic cases.

Q: 9. Would I be able to attach this to a Pelican Case 1485?

A: You could attach the strap clamps on the Pelican Case 1485 loops however, we do not recomend to do so. Nanuk Shoulder Strap for Nanuk cases is desing to clamp on a metal pin. The loops on Pelican cases are too tihck and will prevent the clamps from closing all the way, therefore is not safe. Also the strap would need to come off in order to open and close the Pelican case.

Q: 10. Does the gimbal fit when set at different balance configurations? Essentially, do you need to reset the gimbal's physical setup every time you pack it in the case?

A: Yes, you would need to reset the gimbal's physical setup to fit it in the Nanuk Waterproof Hard Case with Custom-Cut Foam Insert for DJI RS 3 and RS 3 Pro Combo (Black). However, the DJI RS 3 and Pro gimbal settings and plate have scale markings so that even when disassembled you will be able to mount the camera in the proper position so it will be balanced every time.