Made of injection-molded, ultrahigh-strength polyethylene, this SKB Cases R-Series 3722-20 Wheeled Utility Case is made to withstand the most extreme and demanding shipping, handling, and working conditions. The empty interior allows for full use and customization of the interior space. To accommodate a wide assortment of gear, this case has a roomy 37.5 x 22.25 x 20" interior. Two hinged handles allow you to carry the case by hand, or if it's too heavy you can extend the pull handle and tow it behind you on its two skate-style wheels.

Design features include gasket sealing to an IP67-rating that makes the case dust and waterproof. Seven latches on three sides compress the gasket in the lid to seal it against water and dust. It is resistant to a variety of hazards that you may encounter including impacts, ultraviolet (UV) radiation, solvents, corrosion, and even fungi. A pressure relief valve comes into play especially during air transport by regulating the internal pressure, keeping your gear and the case from ge that may develop.

Airtight and Waterproof    Large 37.5 x 22.25 x 20" Interior    Built for Extreme & Demanding Conditions    Empty Interior for Full Customization    Polypropylene Copolymer Resin    UV/Solvent/Corrosion/Fungus Resistant    Retractable Handle & Skate-Style Wheels    Recessed Latches and Handles    Built-In Pressure Relief Valve

Related Questions and Answers

Q: 1. Is this case acceptable for travelling internationally? Airline got 50lbs limit for check-in baggage.

A: It is accepted, but because it weighs 11 pounds, you only get 40 to fit in. I've found I can put a tripod, small light stands, slider and some other misc. stuff and keep it right under 50. A VERY solid case, nothing is going to get dinged when it's in this thing. Length is also fine for the airlines, though I've found sometime it's delivered to oversize luggage.

Q: 2. How much does it weigh with the think tank dividers inserted?

A: The SKB 3i-Series 4213-12 Wheeled Waterproof Utility Case combined with the Think Tank Divider Set is approximately 29lbs.

Q: 3. Could this case hold a Manfrotto 525MVB and 3 or 4 light stands?

A: I don't believe so - unless those light stands were very small. Even then it would be tight.

Q: 4. Will this Case fit a Libec LX7 Tripod With Fluid Head and Floor Spreader?

A: Yes, the HPRC 6300TRIB will fit a Libec LX7 Tripod with Fluid Head and Floor Spreader.

Q: 5. Will the Sachtler Video 18 FT MS flowtech 100 Tripod System fit in this case when it is in the Sachtler soft case?

A: This case will fit the tripod system from B&H # SA1811FTMS very well. You may be able to squish the soft case that the tripod comes with, within this case, but it is not something we recommend or know for sure that is possible.

Q: 6. Can I use Flowtech 75+ACE L?

A: Yes, a Flowtech 75+ACE L will fit into the HPRC 6500TRIB Wheeled Hard Case for Tripods with Soft Interiors Kit (Black).

Q: 7. Could you fit 2 tripods in this case measuring roughly 35" x 8" each?

A: Interior Dimensions 36.4 x 10.6 x 9.6" , if they meat this dimensions

Q: 8. Can this case fit multiple tripods? I have a few Manfrotto MVH502A w/ 546b tripods. It would be nice if I could get them all in one haul!

A: No, you would not be able to get multiple Manfrotto MVH502A Fluid Head and 546B Tripod Systems in the HPRC 6300TRIB Wheeled Hard Case. You may be able to place a slim light stand next to the tripod, but multiple 546B Tripods would not be able to fit inside a single case.

Q: 9. Can this be checked as airline baggage?

A: The SKB 3i-Series 4213-12 Wheeled Waterproof Utility Case is 45.51 x 16.02 x 12.95" which is about 75 linear inches. Most airlines have a limit of 62 linear inches for checked luggage and 45 inches for carry on. Please contact your airline for more specific information as well as alternative options they might be able to offer.

Q: 10. How many Avenger 5034 wheeled stands plus boom extensions can this hold?

A: One Avenger 5034 stand would fit in the HPRC 6500 Wheeled Hard Resin Case with Tripod Holder Kit (Black).