Extend your original Sony PXW-FX9 camera handgrip using this Sony Multiport Extension Cable from Chrosziel. The cable measures 24" in length and allows you to extend the original FX9 handgrip for use with optional extension arms and rigs. It has a female Multiport connector on one end and a male Multiport connector on the other end. One cable tie is also included.

Connects to Sony PXW-FX9 Handgrip    Extend Existing Multiport Cable by 24"    Male to Female Adapter Cable    Cable Tie Included    Works with Original Camera Grip

Original Sony PXW-FX9 handgrip

Related Questions and Answers

Q: 1. Can I have a Sony battery in the camera simultaneously for hot swapping while this is attached?

A: The Small Battery that the FX9 comes with can be installed in behind this unit.

Q: 2. Will this work for the FX6 top handle? to be able to have/mount the top handle off camera.

A: The MID49 EVF/LCD Extension Cable (Sony Burano, FX9, and FX6) is an extension for Sony's 40-pin monitor system found on recent cameras, including: Burano, FX9, FX6, FS7, FS7mkII, FS5, and FS5mkII. It only connects to the EVF/LCD and does not allow you to reposition the handle. Here's an optional offset adapter: the MID49 ARRI 3/8-16 to M4x20mm Offset Adapter (B&H # MI9CBLBK38M4), which is a grid of M4 holes spaced 20mm apart with a 3/8-16 screw and locating pins in ARRI spacing. The locating pins can be removed and repositioned if needed.

Q: 3. If ordered now will this be the new model ,as in the picture ?

A: Yes, you will receive a brand new model, the same as pictured.

Q: 4. With this fully installed on an FX-9, do you have a case you could recommend for field shoots, being able to take the rig in and out quickly and easily on multiple set up and multiple location shoots?

A: Without knowing more specs about your set up (what lens are you using, do you need compartments for additional accessories etc) it is hard to make a recommendation via this platform. Please reach out to our sales team either by phone at 1-800-606-6969 or by email at sales@bhphoto.com with all the requirements for your case and we will do our best to make a recommendation for you.

Q: 5. Does this assembly work on FX6 VF?

A: The Sony Eyepiece Loupe Assembly for PXW-FX9 is not compatible with the Sony FX6.

Q: 6. Would this work with the FS7?

A: No, the Vocas Run and Gun Shoulder Kit for Sony PXW-FX9 is designed specifically for the Sony PXW-FX9 XDCAM 6K Full-Frame Camera System and not the Sony PXW-FS7 XDCAM Super 35 Camera System.

Q: 7. Does it work with the FX6 also?

A: No it does Not

Q: 8. Greetings. Will SONY's Grip Remote Control that's included with SONY FX-9 mount to this rig, or will I need additional mounting hardware to attach the Grip Remote Control?

A: Hello Martin, Thank you for your question! In order to attach the remote grip from Sony, you will need our FX9RH. Like other Sony remote grips, you'll need to disassemble it from its factory setup and insert the grip part into our remote extension handle. You can see our unit on our website: https://www.shapewlb.com/sony-fx9-remote-extension-kit/. We hope this helps and we thank you for your interest in our products. The SHAPE team

Q: 9. Does this allow for higher voltage than 19.6V, namely 24V?

A: No, the IndiPRO Tools Regulated D-Tap to DC Barrel Power Cable for Sony PXW-FX9 (BH #INDTSFX9 • MFR #DTSFX9) will only output at 19.5V.

Q: 10. Would this plate fit a Sony FS7?

A: No, This SHAPE rear Insert plate is specifically designed for the Sony FX9. Please use this plate for the Sony FS7. https://bhpho.to/3CmbFBa