The Singular Sound Breakout MIDI Cable for G2M (Version 3) converts the MIDI out of the G2M into a MIDI out and a MIDI in. The MIDI out is essentially a through, so you can continue to connect the G2M to your synths. The MIDI in lets you send MIDI controllers to the G2M to control your performance. The cable supports MIDI hold, sustain, and volume MIDI messages.

ript>

Converts MIDI Out to In/Out

Related Questions and Answers

Q: 1. So, do the two USB-A connectors plug into those on a PC and the USB-C end plug into the recorder to power it? If so, could I use this with an external USB powerpack that has two USB-A out connections to power the recorder and phantom powered external mics for a period of several hours? (Instead of using Sony L-mount batteries?)

A: Hi Ross, You are correct: the two USB-A connectors would plug into your computer and the USB-C end will connect to your MixPre 3/6 to power it. Yes you can also use a USB Powerpack to power your MixPre-3/6. Just in case here are additional powering options for your reference: https://www.sounddevices.com/tech-notes/mixpre-3-mixpre-6-powering-options Thanks!

Q: 2. Is this compatible with the Yamaha Reface series?

A: No, the RME MIDI I/O Breakout Cable with Two 5-Pin DIN Jacks for Babyface Pro Audio Interface is not compatible with Yamaha's Reface series devices.

Q: 3. How long does it last?

A: Thank you for your question. It will depend on size of battery and the amount of channels you are using with phantom power.

Q: 4. Is this the correct cable to connect the SmallHD Indie 7 with Red Komodo Control to the RED Expandsion module Ctrl port for Komodo?

A: Yes it is. This cable will connect your indie 7 monitor to the Red Komodo.

Q: 5. would this work to jam sync between a timecode solutions UltraSync one and a dji osmo Pocket 3?

A: Theoretically, you can use the Sound Devices BNC to USB-C Timecode Cable for A20-Mini to jam sync the Atomos UltraSync ONE RF Timecode Sync for AtomX Sync and Ninja V with the DJI Osmo Pocket 3. However, according to DJI, they have not specifically tested if timecode via BNC will pass through the USB-C port of the Osmo Pocket 3.

Q: 6. A rep from Tilta is telling me that this will also send video signal to the SmallHD Focus Pro OLED, so that I can see video. Is this true?

A: The SmallHD Monitor/Camera Control Cable for DSMC2/RED KOMODO, does not carry a video signal. You would still need to connect an SDI cable from your camera to the monitor to carry a video signal.

Q: 7. Does this work with the Yamaha DGX-300?

A: The Art MConnect USB MIDI cable is compatible with the Yamaha DGX-300.

Q: 8. Does this unit regulate power? I want to use this with a V-mount battery, but concerned about sending too much voltage to my MixPre-6 (original version). I can't find any power voltage specs in the MixPre owner manuals.

A: Yes, the Cable Techniques MX-POWERSLED for Sound Devices MixPre-3 And MixPre-6 sends a regulated 7.2V DC power input to the MixPre and accepts a 9-24V DC input range from external sources.

Q: 9. Is the distance from each TS connector to the Y-junction 5' (i.e. total spread 10')?

A: No. the distance from the tip of the 1/8" connector to the tip of either of the TS connectors is 10'. The distance from each TS connector to the y-junction is considerably shorter than 5'.

Q: 10. will this work with Mix Pre 3 II which is rated at 5V?

A: Yes the Cable Techniques MX-POWERSLED will work fine with the MixPre 3 or 6. The recorder regulates the voltage required not the battery sled.