Eliminate floor cables by adding up to eight wireless headsets to your PortaCom & Anchor Audio wired intercom system with this Eartec HUB Interface. By linking the HUB Interface to both the HUB Mini Transceiver Base Station (available separately) and your PortaCom & Anchor Audio wired system, this wireless-to-wired interface enables up to eight wireless users to roam freely and communicate in full duplex with the partyline—handsfree—just as if they were plugged into the wired system by cable.

For PortaCom & Anchor Audio Systems    Full Duplex for up to 8 Wireless Users    2 Channels of Communication    900' Range in All Directions    Operates in Non-Licensed DECT Band

• For PortaCom & Anchor Audio wired intercom systems
• Plugs into HUB Mini Transceiver Base Station (available separately)
• Full duplex for up to 8 wireless users
• 900' range in all directions
• 2-channels of communication (separate headsets on channels A & B, or link entire team with the push of a button)Operates in the non-licensed DECT band

Related Questions and Answers

Q: 1. Is it possible for me to run a feed from my mixing console into the Eartec Hub using this interface?

A: No. This Eartec HUB Interface is intended specifically for use to connect a Clear-Com wired intercom system with an Eartec HUB intercom system.

Q: 2. I want to courier these to South Africa.The couriers want to know the watts/h . Can't find that info! Pls help

A: The Eartec Rechargeable 3.7V Lithium-Ion Battery for UltraLITE & HUB Systems is rated at 800mAh, 3.0Wh. You can see the information in the photo, printed on the battery.

Q: 3. Will this work with 2 Wire and 4 Wire Clearcom systems?

A: The Eartec HUB Interface for ClearCom Systems (BH # EAHUBINCC) works with ClearCom 2-wire and 4-wire systems.

Q: 4. Could this function as a passive volume controller with 2 computer inputs via USB?

A: No, it can not be used as a passive volume knob for your computer.

Q: 5. is it ok for atem talkback converter ?

A: The Eartec HUB HUBINCC Interface is intended for use with a Clear-Com Intercom System to enable up to eight wireless users to communicate with users of an Eartec HUB Intercom System. It is not compatible for use with Blackmagic Design ATEM switchers.

Q: 6. Does this identify as 4x separate outputs (mains & monitors) in a DAW?

A: No, this will only give you the main stereo output signal in both main outs and headphones.

Q: 7. I have the 4 pack eartec headsets, that work with master headset and 3 slaves. For the hub interface to clearcom, will I also need to buy the Hub? So will I need both the hub and hub interface?

A: Yes, you will need to use the HUB (B&H # EAHUB) and the HUB interface together. The HUB works in the same manner as the master headset you already have, so it replaces the master headset. The HUB can be used with eight wireless UltraLite remote headsets and one wired headset.

Q: 8. I have an older eartec that uses NiMH Battery. Can I change them and use lithium batteries?

A: Please use the original type battery chemistry.

Q: 9. What is the best way to store these batteries when not in use for a day, month, or year?

A: Lithium ion batteries should be stored in a cool dry place and charged with approximately 30 to 50% power remaining (not fully drained). Make sure the battery contacts are protected so the battery will not short out if something were to touch the contact points. Many lithium ion batteries come with a cover that protects the contact points. Electrical tape can also be used for this purpose. Batteries can be left in the device when it is not used for a few days, but should be removed from the device if it will not be used for a week or longer. This will help to extend battery life and also prevent possible damage to your device.

Q: 10. I am looking to use the Hub to connect a Whirlwind THS-4 instead of a comm system. Is this possible?

A: The Eartec Hub systems are not designed to be adapted into the the Whirlwind THS-4 system.