Amplifier With Subwoofer Output

Ashly Nx3.04 Programmable Output Power Amplifier

Product Code: ga9204
Availability: In Stock

$14,037.00 $21,336.24

Qty

3 reviews Write a review

Description
Reviews (3)

The Ashly NX3.04 Programmable Output Power Amplifier features lightweight, energy efficient Class D switching amplifier technology combined with a switch mode power supply. The NX3.04 amplifier is designed to meet the needs of demanding live sound and fixed installation sound systems in stadiums, arenas, performance venues, worship spaces, and convention centers.

The NX3.04 is a base level amplifier, available in either 2 or 4-channel models. Use rear panel DIP switches to program each channel output for either High-Z (70V or 100V Constant Voltage) or Low-Z (stable down to 2Ω) operation. When in Sleep Mode, the NX3.04 amplifier draws less than 1W.

Parameters
Output Power	Per Channel, EIAJ Test Standard, 1 kHz, 20 Hz to 20 kHz, 1%THD, Low Z Output, All Channels Driven 2 Ω: 3,000 W 4 Ω: 2,000 W 8 Ω: 1,250 W Low Z output, Bridge Mode, 20 Hz to 20 kHz, 1%THD, All Channels Driven 4 Ω: 6,000 W 70 V, 100 V Output, All Channels Driven 70 V (per channel): 2,450 W 100 V (per channel): 1,250 W
Power Draw	Sleep Mode: < 1 W Standby Mode: 70 W Idle (no signal): 100 W
Current Draw	120 VAC Mains (Divide by 2 for 240 V) Sleep Mode: 0.1 A Standby Mode: 1.30 A Idle (no signal): 1.85 A All Channels Driven (Divide by 2 for 240 VAC) Typical: 29.5 A
Dissipation	Thermal (All Channels Driven) Sleep Mode: 3.4 BTU/hr Standby Mode: 238 BTU/hr Idle (no signal): 340 BTU/hr Typical (1/8 maximum power): 2720 BTU/hr
Voltage Gain	Selectable at 26 dB, 32 dB, 38 dB, or 1.4 V
Damping Factor	>250 (8 Ω load <1 kHz)
High-Pass Filter	Input: 80 Hz 2nd order
Distortion	SMPTE (typical): <0.5% THD-N (typical): <0.5% (8 Ω, 10 dB below rated power,20 Hz to 20 kHz)
Channel Separation	-75 dB (dB from full output, 1 kHz)
Signal to Noise Ratio	20 Hz to 20 kHz (unweighted): >114 dB
Frequency Response	20 Hz to 20 kHz, +/-0.05 dB
Input Connector	Balanced: Euroblock 3.5 mm, 1/4" TRS and XLR Combo jack
Input Impedance	10 kΩ
Maximum Input Level	+21 dBu
Output Connector	Speaker: Neutrik speakON
Connection	Data: Euroblock 3.5 mm - Gnd, 18 V, In, Out
Level Control	Remote DC: Euroblock 3.5 mm - Gnd, CV, V+ per input
Attenuation	Per Channel: Front panel, software, offset link group, and remote. Fully off = Mute
Protection	Amplifier: Inrush current limitation, temperature monitoring, output over-power protection, mains fuses
Cooling	Continuously variable temperature controlled axial fan(s)
Environmental	32 to 113˚F (0 to 45˚C) non condensing
Dimensions	19.0 x 3.5 x 16.8" (482.6 x 88.9 x 426.7 mm)
Weight	< 28.0 lb (12.7 kg)
Packaging Info
Package Weight	34 lb
Box Dimensions (LxWxH)	19 x 16 x 4"

2 and 4-channel high-output, lightweight amplifier with programmable output on each channel (Hi-Z or Lo-Z, selected via rear panel DIP switches)

Power-saving, Energy Management System (Ashly EMS) automatic <1W Sleep-mode (defeatable)

Front panel power switch and level controls (can be disabled for security)

Front panel LEDs for temperature, current, signal, clip, mute, bridge mode, protect, sleep, and disable (of front panel controls)

Neutrik Combo XLR - 1/4" TRS jack plus Euroblock input connectors

Neutrik speakON twist locking loudspeaker connectors for security, safety, and reliability

Rear panel DIP switches per channel for selection of high pass filter, limiter, input gain, and High-Z or Low-Z speaker output configuration

Remote DC level control on each input channel

Neutrik powerCON detachable AC mains connector

Switch mode power supply automatically detects 120 or 240VAC operation

Extensive protection circuitry, continuously variable cooling fans

Multiple independent internal power supplies provide increased channel separation and reliability

Related Questions and Answers

Q: 1. Why is this Marantz amplifier so expensive and it does not even have decent 4ohm performance. A lot of metal though.

A: This amplifier is not a stock item, and it is currently selling for list price. It's not for everybody.

Q: 2. Does the Marantz stereo power amplifier has a midrange sound control?

A: This power amp does not have tone control. A preamp would be paired with this amp, and provide for tone control.

Q: 3. Do these power supplies come with a plug-in AC cord? Rhe spec says 3 wire input with strain relief?

A: No. They are designed to be connected directly to the breaker panel.

Q: 4. Does the Ashly ne8250PE amp come with all the Euroblock connectors or do they have to be purchased seperately?

A: The Euroblock inputs are embedded into the rear chassis of the component. No Euroblock connectors ae included as separate DIY items for crimping/soldering onto your own wiring.

Q: 5. can this be installed in digiMIX 18?

A: Yes, the Ashly 32-Channel USB-Audio Input / Output Card can be installed in the Ashly digiMIX 18 18-Channel Digital Mixer.

Q: 6. Is this amplifier CE certified?

A: The Ashly TRA-4150 is Not only CE certified but Safety/Compliance: TUV, FCC, and RoHS.

Q: 7. how do you drive 25v output?

A: Not sure what you are referring to. Please send us your questions via e-mail: AskBH@a href= http://BandH.com target= _blank BandH.com/a

Q: 8. i want to run 2 pair of bose 701's and need 2 sub outputs. is this the rec to buy??

A: No, you will be able to drive just one pair of the 701s with this amp, and there are no sub outs.

Q: 9. Does the Marantz power amplifier sounds like an amplifier with an equalizer?

A: The Marantz MM7025 provides power only, and would be paired with a preamplifier, which would have inputs for your components and equalization adjustments. The Marantz AV7706 11.2-Channel Network Preamplifier with HEOS, BH #MAAV7706 is an example of a preamp that would work well with this power amplifier.

Q: 10. Does ashly have a wireless accessibility?

A: The Ashly Protea 4.8SP does not have a transmitter or receiver built into it for wireless compatibility.

Isaac	26/09/2024
I've amassed a nice little collection of headphones at this point and this is the perfect partner to use most of them with my MOTU M4. It's ridiculously powerful, and even cranked completely up I really don't hear any kind of noise. 5

Stephen	11/06/2024
We installed 4 of these so far and they have worked without issue. Usually we install Speco or Bogen and this was a less expensive unit that did what we needed in this application. 5

Roderick	21/04/2024
I often do offsite recording and was looking for extra headphone outputs for my UAD Apollo Twin audio interface. This was perfect! Sounds great, built like tank and compact for travels and mobile recordings. 5