Db Gain High Pass Filter

Ashly Nxe3.02 Network Power Amplifier

Product Code: ga9205
Availability: In Stock

$10,587.00 $14,927.67

Qty

7 reviews Write a review

Description
Reviews (7)

The nXe3.02 Network Power Amplifier from Ashly Audio is the networkable version of the nX amplifier. It comes with Ethernet control, serial data control, aux preamp outputs, instant standby mode, preset recall, fault condition logic outputs, and optional network audio and digital audio capability. All these are controlled using Ashly Audio's Protea software suite. This amplifier is designed to meet the most demanding live sound and fixed installation sound systems in stadiums, arenas, performance venues, worship spaces, and convention centers.

Ashly EMS 2-Channel Base Level Amplifier 70V, 100V Rated Uses Neutrik Components High-Z / Low-Z Selectable

General
Voltage Gain	Selectable at 26 dB, 32 dB, 38 dB, or 1.4 V
Damping Factor	>250 (8 Ω load <1 kHz)
Filter	Input High Pass Filter: 80 Hz 2nd order
Distortion	<0.5% SMPTE, typical <0.5% THD-N, typical (8 Ω, 10 dB below rated power, 20 Hz to 20 kHz)
Channel Separation	-75 dB (dB from full output, 1 kHz)
Signal / Noise	20 Hz to 20 kHz, un-weighted >114 dB (all 3.0x models)
Frequency Response	20 Hz to 20 kHz, ±0.05 dB
Connector	Balanced Input Connector: Euroblock 3.5 mm, 1/4" TRS and XLR combo jack
Input Impedance	10 kΩ
Maximum Input Level	+21 dBu
Speaker Output	Connector: Neutrik & speakON
Network	Control Network: Compatible with standard 100 MB Ethernet
AUX Outputs	Connector: Balanced Euroblock 3.5 mm Maximum Output: 21 dBu
Contact Closure	Remote Standby: Euroblock 3.5 mm, close contact to GND for standby mode Preset Recall: Euroblock 3.5 mm, close contact to GND for preset 1-4 recall
Data	Data Connection: Euroblock 3.5 mm - Gnd, +18 V, In, Out
Level Control	Remote DC: Euroblock 3.5 mm - Gnd, CV, V+ per input
Attenuation	Front panel, software, offset link group, and remote per channel fully off = mute
Amplifier	Amplifier Protection: Inrush current limitation, temperature monitoring, output over-power protection, mains fuses
Cooling	Continuously variable temperature controlled axial fan(s)
Environmental	Non-condensing 32 to 113ºF (0 to 45ºC)
Power Requirements
Power	At 50 Hz Nominal (Automatic Sensing SMPS): 120 VAC Operating Range: 70 to 135 VAC Minimum Power-Up: 85 VAC At 60 Hz Nominal (Automatic Sensing SMPS): 240 VAC Operating Range: 140 to 270 VAC Minimum Power-Up: 170 VAC
Connector	Power Cable Connector: 20 A powerCON
Output	For Max Output Power Per Channel, EIAJ Test Standard, 1 kHz, 20 Hz to 20 kHz, 1% THD & Low Z Output: 2 Ω: 3,000 W 4 Ω: 2,000 W 8 Ω: 1,250 W For Low Z output, Bridge Mode, 20 Hz to 20 kHz & 1% THD: 4 Ω: 6,000 W For Output Per Channel: 70 V: 2,450 W 100 V: 1,250 W Note: All Channels Driven
Power Draw	Sleep Mode: < 1 W Standby Mode: 40 W Idle (No Signal): 55 W Note: All Channels Driven
Current Draw	For 120 VAC Sleep Mode: 0.1 A Standby Mode: 0.70 A Idle (No Signal): 1.00 A For 240 VAC Sleep Mode: 0.2 A Standby Mode: 0.35 A Idle (No Signal): 0.5 A Maximum for all Channels Driven: For 120 VAC Typical: 14.7 A For 240 VAC Typical: 7.3 A
Dissipation	Thermal Dissipation: Sleep Mode: <3.4 BTU/hr Standby Mode: 136 BTU/hr Idle (no signal): 187 BTU/hr Typical (1 / 8 Max Power): 1,360 BTU/hr Note: All Channels Driven
LED Indicators	Front Panel LED Indicators: White LED: Power Switch: On, off, standby (flashing) Red LED: Clip / Mute Per Channel: Clip @ 1 dB below full output / mute Protect: On, Off Green LED: Signal Per Channel: -18 dBu Bridge Per Channel Pair: On, off Com: On, for Ethernet data or device ID Current Per Channel: Proportional to output Yellow LED: Temperature Per Channel: On dim at 90% max operating temperature, full bright + protect at 100% Sleep: On, amplifier is asleep from audio inactivity Disable: On, power switch & front panel attenuators are disabled
Processor
Input Source	Protēa DSP Options: Analog, auto (net, AES3, analog) Note: All DSP functions can be linked to 1 of 16 link groups
Limiter	Brick Wall Limiter: Threshold: -20 to 20 dBu Ratio: Infinite Attack: 0.2 to 50 ms/dB Release: 5 to 1000 ms/dB
Control	Advanced Gate Controls: Key Engage Enable: Yes Key Frequency: 20 Hz to 20 kHz Key Bandwidth: 0.016 to 3.995 octave
Gain	Gain (with / without VCA): -50 to 12 dB, off, polarity invert Digital VCA Groups: 4 available Remote RD8C Gain: Enable per channel, 0 dB to -∞ WR-5 (neWR-5) Remote Gain: 0 to -50 dB, mute
EQ Type	For 31-Band Filter Type: Constant Q or proportional Bandwidth: 0.499 octave to 0.25 octave For Parametric 2,4,6, or 10 Band Frequency: 20 to 20 kHz Level: -30 to 15 dB Q Value: 0.016 to 3.995 octave For Hi / Low Shelf 6 / 12 dB/octave Frequency: 20 Hz to 20 kHz Level: -15 to 15 dB For All Pass Frequency: 20 Hz to 20 kHz For Variable Q HP / LP Frequency: 20 Hz to 20 kHz Q Value: 3.047 to 0.267 For Notch / Bandpass Frequency: 20 Hz to 20 kHz Q Value: 92.436 to 0.267
Crossover	2 Way, 3 Way, 4 Way Crossover & High Pass / Low Pass Filters Bessel & Butterworth Filters: 12 / 18 / 24 / 48 dB/octave Linkwitz-Riley Filter: 12 / 24 / 48 dB / octave Frequency: Off, 20 Hz to 20 kHz
Delay	Sampling Rate: At 48kHz (Input Time, Distance & Temperature) Speaker Delay: 0 to 21 ms Delay: 0 to 682 ms At 96 kHz (Input Time, Distance & Temperature) Speaker Delay: 0 to 10.6 ms Delay: 0 to 341 ms
Audio Metering	Range: -60 to 20 dBu Increments: 1 dB Peak Hold Indicator: Yes
Signal Generator	Pink Noise, White Noise, Sine Wave Signal Level: Off, -50 to 20 dBu Sine Wave Frequency: 20 Hz to12 kHz
Processor	Input A/D, Output D/A: 24 bit DSP Processors: 32-bit floating point Sample Rates: 48 kHz, 96 kHz Propagation Delay @ 48 kHz: 1.42 ms Propagation Delay @ 96 kHz: 0.71 ms
Mixer	Gain (0.5 dB Increments): Off, -50 to 12dB Mute: Per channel Auto-mixer Enabled: Per channel Global Auto-mixer Response: 0.01 to 2 sec Enable Ducking at Mixer: Yes Ducking LED: Per channel if enabled Metering: Level, auto-mixer level
Filters	Number: 12 In/Out per filter: Yes Lock per filter and global lock: Yes Filter Modes: Float, Restricted, Manual Filter Type: Notch, Parametric Filter Frequency Range: 20 Hz to 20 kHz Notch Filter: -∞ Parametric Filter: 15 dB to -30 dB Filter Bandwidth: 0.016 to 3.995 octave Detector Sensitivity: 5 levels Float Time: 5 minutes to 24 hours
Compressor
Threshold	-20 to 20 dBu
Ratio	1.2:1 to infinite
Attack	0.2 to 50 ms
Release	5 to 1000 ms/dB
Detectors	Peak / average
Attenuation	2 available
Metering	In, out, attenuation, graphical
Controls
Level	Target Level: -40 to 20 dBu
Action Type	Gentle, normal, aggressive, user defined
Maximum Gain	0 to 22 dB
Metering	Input, gain, attenuation
Ratio	1.2:1 to 10:1
Threshold	-30 to 0 dB
Gain	5 to 1000 ms/dB
Hold	0 to 6 seconds
Noise Characteristics
Gain	Maximum: -20 to 20 dB Minimum Base: -40 to 20 dB
Gain Adjustment Range	0.2 to 20 s/dB
Groups	Link Groups: 16 available
Input Channels	ANC: 1 to 2 or 1 to 4
Threshold Range	Noise: -40 to 20 dBu
Ratio	Program/Ambient Gain: 0.3:1 to 3:1
Metering	Input level, attenuation, average noise
Ducking	Trigger Threshold: -80 to 20 dBu Ducking Release: 5 to 1000 ms/dB Ducking Depth: 0 to -30 dB, -∞ Enable Ducking at Matrix Mixer: Yes Metering: Input
Gate
Threshold	-80 to 20 dBu
Range	Off, 100 to 0 dB
Attack	0.2 to 50 ms/dB
Release	5 to 1000 ms/dB
Metering	Key signal, gate LED, graphical
Dimensions	19.0 x 3.5 x 16.8" (482.6 x 89.0 x 426.7 mm)
Weight	< 28.0 lb (12.7 kg)
Packaging Info
Package Weight	31 lb
Box Dimensions (LxWxH)	19 x 16 x 4"

2-channel high-output, lightweight amplifier with programmable output on each channel

Power saving, Energy Management System (Ashly EMS) automatic <1W sleep mode is defeatable

Front panel power switch and level controls can be disabled for security

Neutrik Combo XLR: 1/4" TRS jack plus Euroblock input connectors

Neutrik speakON twist locking loudspeaker connectors for security, safety, and reliability

Rear panel DIP switches per channel for selection of high pass filter, limiter, input gain, and High-Z or Low-Z speaker output configuration

Ethernet port for use with control and monitoring of amplifier functions, with front panel COM activity LED

Serial data port for use with Ashly remote control devices, or RS-232 converter (sold separately) for third party controllers (INA-1)

Uses Protea software to remotely disable all front panel controls, including the on/off switch, for a tamper-proof installation

Real-time clock with event scheduler

Instant standby mode, 30% reduction in power consumption with on/off triggered by contact closure, software control, or event scheduler

Programmable power-on delay

Preset recall via contact closure, software control, remote control, or event scheduler

Auxiliary preamplifier outputs and fault condition logic outputs

Cobranet or Dante network audio (sold separately) and AES3 digital audio input with pass-through

Ducking at mixer, peak hold indicator, in/out per filter, key engage, lock per filter, and global lock

Related Questions and Answers

Q: 1. When used in the bridged mode for mono, will the headphone output be mono as well?

A: When cue monitoring with headphones on the Samson Servo 120a, you will receive a stereo signal in the headphones.

Q: 2. Shall we equalize the sounds with low, medium and high frequencies?

A: The Audiolab 6000A does not have EQ controls.

Q: 3. Can this be powered by Ac input 220v?

A: This device 120V AC/60Hz only.

Q: 4. Can I hook an equalizer to the Marantz power amplifier?

A: Unfortunately newer Amplifiers (and Receiver Amplifiers) no longer offer the ability to connect a separate Equalizer like the older models. The current models no longer provide Input / Output ports for Equalizers.

Q: 5. If your amplifier is CE certified can I get testimony from you to that effect?

A: You can find Ashly's certifications by following the link below, and clicking on the 'features' tab. https://ashly.com/tra-convection-cooled/

Q: 6. i want to run 2 pair of bose 701's and need 2 sub outputs. is this the rec to buy??

A: No, you will be able to drive just one pair of the 701s with this amp, and there are no sub outs.

Q: 7. Does the Ashly ne8250PE amp come with all the Euroblock connectors or do they have to be purchased seperately?

A: The Euroblock inputs are embedded into the rear chassis of the component. No Euroblock connectors ae included as separate DIY items for crimping/soldering onto your own wiring.

Q: 8. Can you connect a subwoofer to this amp?

A: No

Q: 9. does this unit plat SACD Discs?

A: The Audiolab Omnia Stereo 100W Network Amplifier and CD Player does not play Super Audio CD (SACD).

Q: 10. how do you drive 25v output?

A: Not sure what you are referring to. Please send us your questions via e-mail: AskBH@a href= http://BandH.com target= _blank BandH.com/a

Richard	12/09/2024
Pared this with the Marantz AV7705 processor and couldn’t be happier. Clean powerful sound driving my Boston Acoustic VR-M90’s. Have battled for 14 years with a intermittent AC ground loop hum with my former Outlaw Audio equipment. Now, no more hum! Thank you Marantz! 5

CNLTDUB	11/09/2024
I have been listening to this unit for about a year now. It's paired with Dynaudio Evoke system. I come from years of Car Audio SQ competition, and Home audio system. This has blown me away for the price vs. performance. This amp can beat the hell out of these speakers when asked...and stays poised the entire time. The SQ is amazing for the speakers price point. 5

Duke	07/09/2024
Great unit. I’m very happy with it. I’m running energy connoisseur speakers 5.1 system. Should I get the MM7055? 5

Martin A	27/08/2024
Best purchase ever must have for music quality enthusiast. Having a power amp allowed me to also add in professional equalizer to my SR 5011 receiver. Provided power to drive the surround speakers to turn up the movies and music experience to another level which was unachievable with the SR 5011 receiver alone 5

Howard	27/05/2024
Is a great amp ? My are you asking me now I 5+ years but it working great l love it 5

Jay G	08/05/2024
Great clean power reliable performance. Using with Marantz 8055 5

Tumi	01/05/2024
Paired with the Marantz AV7705, this amplifier performs admirably. I am a fan of the Marantz sound and this pair does not disappoint. 5