The WiMi6220 Wireless 3G-SDI & HDMI H.264 Encoder/Transmitter from Nimbus pairs with an optional WiMi6220 receiver as a point-to-point Wi-Fi transmission system with a 4921' range and only 80ms latency. With both units featuring built-in 5 GHz Wi-Fi, no additional network connection is required. This model can be powered using the included Gold mount battery plate or via the 2-pin LEMO power connector for continuous power.

The transmitter encodes and sends up to a 1080p60 SDI or HDMI signal as an H.264 encoded signal, and the receiver decodes and outputs it as video. The transmitter is also capable of multicasting to up to four receivers at the same time over the same range and with the same near-zero delay.

An Ethernet port, which allows for CCU/PTZ camera control, can also be used for wired connectivity and 1080p60 transmission to the receiver via Cat 5e cable. The WiMi6220 transmitter also features an RS-422 interface and a two-way talk-back audio jack. With a corresponding audio jack available on the receiver, the talk-back port allows connecting a headset mic for communicating with talent. The WiMi6220 transmitter offers a 1/4"-20 mounting thread on the bottom.

1 x 3G-SDI/HDMI Transmitter/Encoder    2 x 3G-SDI/HDMI Receiver/Decoders    4921' Range over 5 GHz Wi-Fi    Up to 1080p60 Video Signals, H.264 Codec    Gold Mount Battery Plates on Each Unit    Power Adapters, RJ45 Adapter for RS-422

• 4921' range over 5 GHz Wi-Fi
• 80ms latency
• Includes Gold mount battery plate
• Encodes and sends up to a 1080p60 SDI or HDMI signal in H.264 MPEG-4 Parts 10: AVC (decoded by optional receiver)
• RTSP streaming server (RTP/UDP)
• MPEG2TS streaming (UDP)
• 3G/HD/SD-SDI and HDMI inputs
• Ethernet port for CCU/PTZ control or wired connectivity and 1080p60 transmission
• Two-way talk-back audio jack for headset mic communication
• RS-422 interface
• Baseline profile with level 4.2
• 2-pin LEMO power input
• USB firmware update port
• 1/4"-20 mounting thread

Related Questions and Answers

Q: 1. Can this Unit convert SDI input in TX to HDMI output in RX ?

A: The Shimbol ZO600S SDI & HDMI Wireless Video Transmission System does not list cross conversion between HDMI and SDI.

Q: 2. the latency please ?

A: The SWIT CURVE500 HDMI Wireless Video Transmission System has a latency of less than 50ms.

Q: 3. Is there any other piece of hardware holding this adapter onto the camera aside from the V-Mount itself?

A: The Wooden Camera D-Box for Sony Burano Camera (Gold Mount) attaches directly to the back of the camera. However, the included Wooden Camera B-Box System for Sony BURANO would require a top plate for it to attach to. Wooden Camera Top Plate for Sony BURANO BH #WOA00531

Q: 4. I'm using an SDI splitter on an FX6. Feeding Ninja 4k60 but client monitor only needs 1080. Will this down covert a 12G signal?

A: The Accsoon CineView SE Multi-Spectrum Wireless Video Transmission System will not down convert a 4k60p signal. The Accsoon CineView SE Multi-Spectrum Wireless Video Transmission System can only accept up to a 1080p60 fps signal via SDI.

Q: 5. This system came up when I filtered for "uncompressed" wireless systems. Is it truly uncompressed? Is there any quality loss?

A: The SWIT CURVE500 HDMI Wireless Video Transmission System is compressed. This model uses H264 compression. Please see below for SWIT's uncompressed wireless solution. SWIT FLOW500 SDI & HDMI Wireless Video & Audio Transmission System BH #SWFLOW500

Q: 6. Can I input HDMI and output SDI or vice verça?

A: No, the Lilliput WS500 Wireless Video Transmission System does not have a HDMI to SDI cross conversion function. SDI signals would only output from SDI. HDMI would only output from the HDMI port.

Q: 7. Is the power/strength level of the transmitter customizable, or is it always going to consume maximum power from batteries?

A: It does not have power/strength settings.

Q: 8. Can I pair it with a Goast-eye 600MP receiver?

A: Yes, this offers cross-compatibility with other Ghost Eye receivers.

Q: 9. can we use this device to stream over public network ? If yes how

A: The WiMi6220 Wireless 3G-SDI & HDMI H.264 Encoder/Decoder Set from Nimbus is a point-to-point Wi-Fi transmission system. With both units featuring built-in 5 GHz Wi-Fi, no additional network connection is required. The transmitter encodes and sends up to a 1080p60 SDI or HDMI signal as an H.264 encoded signal, and the receiver decodes and outputs it as video.

Q: 10. Does it transmit Start \ Stop trigger via SDI?

A: The Lilliput WS500 Wireless Video Transmission System can control Start / Stop functionality exclusively from the App controls: "App Display Controls Use the Lilliput app to adjust controls like focus peaking, exposure, zoom, markers, and start/stop recording"