Optimize the performance of your data center, server farm, storage area network, or other high-bandwidth network without getting tangled up in cables with the 50' Belden 10GX Cat 6 UTP EtherCON to RJ45 Ethernet Cable from Laird Digital Cinema. This rugged 4-pair, 23 AWG unshielded twisted pair (UTP) Cat 6 cable features a shielded EtherCON connector on one and an RJ45 plug on the other, providing strong connections with compatible devices. With a diameter of 0.295", the Belden 10GX is designed to save you space while the 625 Hz bandwidth rating supports 10 Gigabit Ethernet speeds at distances of up to 328 feet. The lightweight Belden 10GX is also CMR riser rated and features reduced crosstalk and is protected against harsh electromagnetic emissions from nearby electronics such as power strips, extension cables, and other equipment.

1 x EtherCON Connector    1 x RJ45 Connector    Unshielded Twisted Pair Cable    Slim, Lightweight Cable Design    4-Pair Configuration    23 AWG    Copper Conductor    625 MHz Bandwidth Rating    CMR Riser Rated

Related Questions and Answers

Q: 1. Can this car be added to a windows pc? Also can it be link aggregated?

A: The Synology E10G30-T2 2-Port 10G RJ45 Ethernet to PCIe 3.0 Adapter Card, B&H # SYE10G30T2, is designed to work with specific Synology NAS enclosures, it does not officially support Windows OS. Link aggregation is supported when using it with a compatible Synology NAS.

Q: 2. Can you run HDMI and SDI at the same time? RED GEMINI

A: You will only be able to use one output at a time.

Q: 3. Will this work with the Epic-M Dragon 6k?

A: Yes it will.

Q: 4. Can the GPI port be used as an SDI out? I want to run a Portkeys OEYE EVF and a SmallHD Cine 7 at the same time.

A: No, the GPI cannot be used as a SDI video output.

Q: 5. How would I put a Bright Tangerine Top Handle on top of the RED Outrigger? Is there a NATO Rail with correct screw spacing that would be compatible with the RED Outrigger?

A: The outrigger has mounting holes for mounting gear on top of it. Most nato rails are hollow in the center to allow the mounting screws to slide back/forth as needed. For example you may want to consider SmallRig Quick Release NATO Rail (3.9) B&H # SM1134 MFR # 1134

Q: 6. How much does this weigh? (Not the package; the actual item)

A: Approximately 0.97 lbs (440 g)​

Q: 7. Is this compatible with Red Helium 8K?

A: Because the RED Helium 8K is a RED DSMC2 camera, the RED DSMC2 V-LOCK I/O Expander is compatible with the Helium.

Q: 8. Just to be sure. If the Wing Grip mounts on both sides of Komodo, will it work fine with Komodo Outrigger Handle?

A: Yes, The RED DIGITAL CINEMA KOMODO Wing Grip can mount to either side of the Komodo. If you use the Outrigger handle you would not be able to install a wing grip where the outrigger handle is located. So you would only be able to use the KOMODO Wing Grip on one side when paired with the Outrigger handle.

Q: 9. What is the warranty on this ??

A: RED offers a limited 1-Year warranty.

Q: 10. The 4-pin control interface is compatible to run/stop the Komodo with the Tilta Nucleus handgrip Power/Communication 4-pin?

A: It will not be compatible as Komodo protocols are different from standard RED protocols and unless compatibility is explicitly expressed, then the chances of the two products working together is non existent.