Use this Westcott Quick Mount S-Bracket to mount umbrellas and modifiers onto compact lights without causing unwanted stress that can damage your delicate gear. For additional usability, the bracket is outfitted with three cold shoe mounts around its perimeter for speedlights with umbrellas. Made from a combination of aluminum and high-impact plastic, it is compatible with lights up to 3.5" diameter and modifiers weighing up to 4.5 pounds.

To build your rig it has a 1/4"-20 male center mount for your light and a vertical adjustment knob to precisely place the bracket in the light head opening with a 5/8" (16mm) stand thread and an 8mm umbrella thread. Its quick-mount plate can remain attached to your light for future mounting with less time wasted setting up. A built-in tilter bracket with 5/8" receiver adjusts up to 180° for precise light placement. A tension screw securely locks umbrellas in place, and an adjustable Arca-type mounting plate alloys for precise light placement and maximum output. This bracket maximizes flash with Bowens S-Type and umbrella-based modifiers.

Reduces Stress on Light    For Compact Lights and Modifiers    Adjustable Arca-Type Mounting Plate    Screw Locks Umbrella Modifiers in Place    Center 1/4"-20 Male Mount Thread    Aluminum and Plastic Construction    Speedlight & Umbrella Cold Shoe Mounts    Up to 180° Light Placement Adjustment    Adjustable within the Light Head Opening    Payload Capacity: 4.5 lb

Related Questions and Answers

Q: 1. Is this mount compatible with the Westcott FJ400? Or is there another product better suited for the FJ400?

A: The FJ400 already has a Bowens S mount, so the Quick Mount S-Bracket would not be needed.

Q: 2. Can this work with the original tentacle sync?

A: Not that we are aware of. This is specifically for the Sync E, B&H # TETE1.

Q: 3. What is the hole for in the spigot?

A: I've used the hole a few times to tighten, using a screwdriver or hex wrench. Avoid excessive tightening.

Q: 4. Will this bracket work with a HP Compaq LE1911 19" flat panel monitor? It's got 4 screws on the back that look like it would be a fit.

A: Yes, the HP Quick Release Bracket 2 BH #HE69D15AT is compatible with the LE1911.

Q: 5. What is the diameter of the hole, for the umbrella shaft?

A: The diameter is about 9 or 10 millimeters or about 7/16ths of an inch.

Q: 6. Is this mount compatible with the Godox AD-300 Pro?

A: The Westcott Quick Mount S-Bracket has not been tested for use with the Godox AD300pro Outdoor Flash. Instead, I would recommend the Godox S2 Speedlite Bracket for Bowens, B&H # GOS2, for your usage needs with the Godox AD300pro Outdoor Flash.

Q: 7. Can i mount bowens modifiers on this?

A: Yes. We also suggest the following bracket for all Bowens light shaping tools Godox S2 Speedlite Bracket for Bowens BH #GOS2 • MFR #S2 https://bhpho.to/3HXTiop

Q: 8. Is this mount compatible with the Godox AD-200?

A: Yes, It will support the AD200 and AD200 Pro. It also fits any 3rd party light that has a female 1/4"-20 thread.

Q: 9. is this the same as the dual socket magic arm?

A: Diana,This is not the same as the Dual Socket magic arm. It can serve a similar purpose particularly in lighter weight applications.

Q: 10. Would this work with an HP w2408h monitor?

A: The HP Pavilion w2408h is 21lbs making it less than the max 24lb load of the BH #HE69D15AT • MFR #6KD15AT.