Designed to work with unshielded twisted pair (UTP) LAN cables, the red-tinted Simply45 ProSeries Cat 6/6a UTP Unshielded Pass-Through Modular Plug connects onto 23 AWG solid twisted pair LAN cables up to 0.29" in diameter. One-Hundred single piece pass-through modular RJ45 plugs come packed inside of a convenient wide-mouth plastic jar, which work with most Cat 6a and Cat 6 cables in a staggered high/low wire arrangement.

Its patented Cap45 design features a cap/bar that snaps onto the front of the pass-through RJ45 plug after termination, which helps to prevent electrical shorts and other electrical risks by covering the exposed wire ends. Each plug features a 3-prong pin design with 50μ 24kt gold plating to help deliver high electrical conductivity and a stronger connection to wire conductors and has a colored tint for easy identification. These modular plugs are rated to work with PoE and PoH devices.

Unshielded Pass-Through Cat 6/6a Plugs    Integrated Snagless Strain Reliefs    RJ45 Crimp Tool, 5" Flush Cutter Tool    Yellow LAN Cable Stripper

Simply45's 3-prong pins feature 50μ of 24kt gold plating. Having a 3-prong pin provides three points of contact with the copper wire conductor, which provides a strong connection for high electrical performance and improved signal integrity with less heat build-up compared to a 2-prong connection.

The patented Cap45 design features a cap/bar that snaps onto the front of the pass-through RJ45 plug after termination, which helps to prevent electrical shorts and other electrical risks by covering the exposed wire ends.

Related Questions and Answers

Q: 1. Can I use this on a Minolta auto 360px?

A: It is possible to use the Magmod Starter Kit with a Minolta Auto 360 PX, but it hasn't been tested to our knowledge. The results may vary.

Q: 2. Are there additional receivers available? I want to put these on a switch.

A: I'm sorry, but Ocean Matrix does not currently sell the receiver from the Ocean Matrix 1080p HDMI Extender over Single Cat 6 with Loop-Through Output by itself, so for now the receivers are only able to be purchased along with the transmitter.

Q: 3. If a V-Mount battery is installed, does the battery then pass power through to these ports, or is a D-tap cable necessary?

A: Yes, power is passed through to the two 2-pin LEMO-type outputs and two D-Tap outputs. The two 2-pin ports also support power input, so you can utilize external power to your rig.

Q: 4. Does ir Works on dji Rs2

A: The Tilta Power Pass-Through Plate for DJI RS 3/RS 3 Pro (No Battery Plate) is only compatible with the RS3 and RS3 pro models.

Q: 5. Are the two 5VDC adapters compatible with 220-240v?

A: Good Afternoon Richard! The power supplies included in the OMX-HDMI-CAT6 set support 100-240V, so they should work just fine for you. Thank you!

Q: 6. Will this run over Cat 5e?

A: Hi Ryan. These units only support CAT6 and above, so they won't work with CAT5e unfortunately. I apologize for the inconvenience!

Q: 7. Can this work on rs2 with original plate or you need the tilta pass-through for it to wirk. I just need something to attach v out battery under to power camera

A: In order to use the Gold or V-mount plate, the Tilta Power Pass-Through Plate for DJI RS 2 is required.

Q: 8. Could you charge a battery through these ports by using a D-tap charger cable?

A: No, the Tilta Power Pass-Through Plate with V-Mount Battery Plate cannot power the V-Mount battery attached through the D-Tap on the unit. The battery can however be charged with its own D-Tap port.

Q: 9. how is the video qualitydoes it have any rogue pixels?

A: This unit supports resolutions: 480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz, 720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz1080p resolution up to 164 feet (50m)I have not heard of rogue pixels or artifacts being an issue.

Q: 10. Does it Works on DJI Rs4 pro?

A: No, the Tilta Power Pass-Through Plate for DJI RS 3/RS 3 Pro (No Battery Plate) is not compatible with the new DJI RS4 and RS4 Pro Gimbal Stabilizers.